Accel Automobile Parts 140025 User Manual

FORM 1647 02/05  
INSTALLATION INSTRUCTIONS  
AFTERBURNER SWITCHABLE COIL  
#140025  
Reading these instructions before starting the installa- fins for efficient heat dissipation. A mounting/  
tion process will ensure that you will be able to take  
the maximum advantage of all the performance that  
installation hardware kit is included. A universal  
wiring harness is also included. This OEM quality  
your ACCEL Afterburner switchable coil was designed harness is designed to work with most vehicles’  
to deliver. engine compartment layouts.  
The ACCEL Afterburner switchable coil is designed to Step #1  
work on most vehicles equipped with a distributor and  
a single coil type ignition system. It will work with the  
stock vehicles ignition controls as well as most after-  
market inductive storage as well as CD type ignition  
control boxes.  
Choose an area on the fire well or fender well where  
the ACCEL Afterburner coil may be mounted with no  
interference from throttle linkage, air conditioning lines,  
heater hoses, etc. and is no further than 24" from the  
distributor. Please note that the ACCEL Afterburner  
coil may not fit into your original coil’s mounting  
location.  
In the normal mode the ACCEL Afterburner switchable  
coil is designed to boost the amperage available at  
the spark plug for improved low RPM engine perfor-  
mance, maximum load conditions such as when  
towing as well as helping to maximizing your fuel  
efficiency. In the switched mode the ACCEL  
Caution: Before drilling any holes, please check and be  
aware of what you may be drilling into. Be sure not to  
damage a component that may be under or in line with  
a mounting hole.  
Afterburner coil is design to boost voltage at the  
spark plug for improved high RPM performance under  
higher cylinder pressure conditions typically found  
when under boost or using nitrous oxide as well as  
helping to eliminate high RPM misses.  
Step #2  
Use the supplied fasteners in the hardware kit to  
mount the ACCEL Afterburner switchable coil.  
Step #3  
NEVER switch the modes of the ACCEL After-  
burner coil while the engine is running! During the  
time it takes to switch the ACCEL Afterburner coil  
from one mode to the other, several ignition events  
could be missed if the engine was running, even at  
idle speed. This could cause an engine miss-fire  
and resulting in exhaust and/or intake system  
damage. Any vehicle damage that could result  
from switching the ACCEL Afterburner coil while  
the engine is running will NOT be covered under  
the product’s limited warranty nor is any coverage  
of said possible damage is implied.  
The ACCEL Afterburner switchable coil comes with a  
universal wiring harness. This harness must be spliced  
into the vehicles OE wiring harness at the OC coil  
connection using the butt splices connectors  
supplied in the hardware kit. The yellow wire lead in  
the ACCEL harness must be connected to the OE coil  
(+) positive lead, while the black wire lead of the  
ACCEL harness must be connected to the OE coil (–)  
negative harness wire lead. Please refer to your  
specific vehicles’ shop manual for the exact color  
coding of the coil positive and coil negative leads  
before cutting the OEM harness and splicing in the  
ACCEL harness.  
Due to the high-energy output, the ACCEL Afterburner  
switchable coil is supplied with an ACCEL 300+  
8.8mm universal coil lead. The extruded aluminum  
housing/mounting bracket is designed with cooling  
The blue wire lead in the ACCEL harness must be  
connected to a vehicle 12 V switched ignition source.  
ACCEL  
 
1
B) Bend the core conductor back over the wire and  
insert into the terminal.  
arming cover plate over the switch. Note the align-  
ment tab and slot on the arming cover plate and the  
switch. Secure the switch and arming cover plate to  
the switch with the switch nut.  
Step #7  
C) Bend the terminal tabs over with pliers and/or an  
ignition wire-crimping tool.  
Carefully route the ACCEL harness away from any  
linkage, air conditioning lines, heater hoses, exhaust  
manifolds, etc. by using the mounting hardware  
included in the kit.  
Note: For best results, use the ACCEL p/n’s 170036  
or 170037 crimping tool.  
Step #8  
Measure the coil wire to the length. Connect the  
ACCEL 300+ 8.8mm coil wire to the ACCEL  
Afterburner switchable coil and measure the length  
needed to the distributor cap, then add an extra 1/2"  
to 1" to the length. Once the finished length is deter-  
mined, cut and terminate with the supplied terminal.  
MEASURE WIRE TO CORRECT LENGTH  
D) Lightly lubricate the terminal with the dielectric  
grease included and slide the wire into the HEI  
boot. A small amount of dielectric grease may also  
be applied inside of both the distributor and coil  
boot to help prevent any high voltage leakage.  
A) Carefully strip the wire to expose 1/2" to 5/8" of the  
conductor core.  
E) Be sure you have made a good connection on the  
distributor cap and coil. You should recheck these  
connections periodically. If the connector in either  
boot becomes grey-green in color or appears  
corroded, you may have a poor connection.  
DO NOT SLIT THE CORE  
DO NOT SHRED OR STRIP AWAY THE CORE  
You have completed the installation of the ACCEL  
Afterburner switchable coil and you are now ready  
to now enjoy increased ignition performance.  
Remember to NEVER switch the modes of the  
ACCEL Afterburner coil while the engine is  
running!  
ACCEL  
 
3
FORM 1647  
02/05  
Made in U.S.A.  
Printed in U.S.A.  
ACCEL IS A DIVISION OF THE MR. GASKET PERFORMANCE GROUP  
10601 MEMPHIS AVE #12, CLEVELAND, OH 44144  
216.688.8300  
FAX 216.688.8306  
4
 
ACCEL  

3Com Speaker NCG PLM User Manual
Accusplit Watch AE800AC User Manual
Aiphone Welder SBX NVP User Manual
Airlink101 Switch AGSW1600 User Manual
Alesis Electronic Keyboard DG8 User Manual
American Standard Hot Tub 6030Y2A118XXX User Manual
Atlona Microscope Magnifier AT DVIRX RSNET User Manual
Axis Communications Video Gaming Accessories T8640 User Manual
Behringer DJ Equipment DDM4000 User Manual
Behringer Guitar 624 User Manual