Alesis Electronic Keyboard DG8 User Manual

REFERENCE  
MANUAL  
Spring 1999  
 
Your shipping carton should contain the  
following items:  
1. DG8 piano  
2. Sustain pedal  
3. Music stand  
4. AC power cable  
5. Warranty Registration card  
6. Reference Manual  
7. QuickStart Guide  
If anything is missing, please contact your dealer or Alesis immediately.  
Optional accessories available from your Alesis reseller:  
Alesis GS-1 Digital Piano stand w/3-pedal assembly for sustain, sostenuto and soft  
pedal functions  
TM  
Alesis QCard sound-expansion card library  
NOTE: Completing and returning the Warranty Registration card is important.  
ALESIS CONTACT INFORMATION  
Alesis Corporation  
1633 26th Street  
Santa Monica, CA 90404  
USA  
Telephone: 800-5-ALESIS (800-525-3747)  
E-Mail:  
Website:  
TM  
DG8 Reference Manual  
Revision 1.0  
by David M. Bertovic  
© Copyright 1999, Alesis Corporation. All rights reserved. Reproduction in whole or in part is  
prohibited. “DG8”, “QS8.1”, QSR”, “NanoSynth”, “DMPro”, “QCard” and “SoundBridge” are  
trademarks of Alesis Studio Electronics, Inc.  
4
DG8 REFERENCE MANUAL  
 
Contents  
CONTENTS  
Alesis Contact Information ..........................................................................4  
Important Safety Instructions......................................................................7  
Instructions de Sécurité Importantes (French)...........................................................................9  
Beim Benutzen dieses Produktes beachten Sie bitte die folgenden  
Sicherheitshinweise: (German)......................................................................................................11  
Instructions to the User...................................................................................................................12  
CE Declaration of Conformity.......................................................................................................13  
Introduction................................................................................................15  
Typographic Conventions...............................................................................................16  
Getting Started ...........................................................................................17  
What You’ll Need ............................................................................................................................17  
Using the DG8 with Other Equipment.........................................................................17  
Unpack It...........................................................................................................................................17  
Set It Up .............................................................................................................................................17  
Attaching the Music Stand..............................................................................................18  
Setting up the DG8 in a Home .......................................................................................19  
Hook It Up ........................................................................................................................................19  
Power ..................................................................................................................................19  
Sustain Pedal......................................................................................................................19  
The DG8 as a Stand-alone Instrument..........................................................................19  
The DG8 in a Music System............................................................................................20  
Turn It On and Play It....................................................................................................................23  
How the Sounds are Organized.....................................................................................23  
How the Sounds are Selected .........................................................................................25  
Using the Controls............................................................................................................27  
Playing the DG8..........................................................................................31  
Overview...........................................................................................................................................31  
How the Sounds are Organized....................................................................................................31  
Using the Display and Sound Selection Buttons ........................................................33  
Selecting Internal Sounds................................................................................................35  
Using the External Card Sounds....................................................................................40  
DG8 Sound Chart..............................................................................................................43  
Front Panel Controls .......................................................................................................................44  
Tune.....................................................................................................................................44  
Transpose ...........................................................................................................................44  
Effects..................................................................................................................................45  
Graphic EQ.........................................................................................................................45  
MIDI Functions ................................................................................................................................46  
Pedals.................................................................................................................................................48  
Background........................................................................................................................48  
Sustain.................................................................................................................................48  
Sostenuto ............................................................................................................................49  
Soft Pedal............................................................................................................................49  
Pedal Connections ............................................................................................................49  
Audio Inputs and Outputs.............................................................................................................51  
Initializing the DG8 .........................................................................................................................52  
Factory Defaults................................................................................................................52  
Power-Up Resetting .........................................................................................................52  
DG8 REFERENCE MANUAL  
 
5
Contents  
MIDI Functions............................................................................................53  
MIDI Basics .......................................................................................................................................53  
MIDI Hardware................................................................................................................................54  
MIDI Messages.................................................................................................................................54  
Channel Messages: Voice Messages..............................................................................54  
Channel Messages: Mode Messages .............................................................................57  
MIDI and the DG8 ..........................................................................................................................58  
Channel Messages ............................................................................................................58  
Glossary......................................................................................................61  
DG8 Terms ........................................................................................................................................61  
MIDI Terms.......................................................................................................................................62  
Troubleshooting..........................................................................................63  
Cleaning and Maintenance ............................................................................................................65  
Specifications..............................................................................................67  
MIDI Implementation Chart..........................................................................................................67  
Specifications ....................................................................................................................................68  
Warranty ....................................................................................................69  
Index ..........................................................................................................71  
6
DG8 REFERENCE MANUAL  
 
Important Safety Instructions  
IMPORTANT SAFETY  
INSTRUCTIONS  
SAFETY SYMBOLS USED IN THIS  
PRODUCT  
This symbol alerts the user that there are important operating and  
maintenance instructions in the literature accompanying this unit.  
This symbol warns the user of uninsulated voltage within the unit  
that can cause dangerous electric shocks.  
PLEASE FOLLOW THESE PRECAUTIONS  
WHEN USING THIS PRODUCT:  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a damp cloth. Do not spray any liquid cleaner onto the  
faceplate, as this may damage the front panel controls or cause a dangerous  
condition.  
7. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves,  
or other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized plug on the AC power  
adapter. A polarized plug has two blades with one wider than the other. The  
wide blade is provided for your safety. When the provided plug does not fit  
into your outlet, consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched, particularly at  
plugs, convenience receptacles, and the point where they exit from the  
apparatus.  
11. Use only attachments or accessories specified by the manufacturer.  
DG8 REFERENCE MANUAL  
 
7
Important Safety Instructions  
12. Do not place this product on an unstable cart, stand, or table. The product  
may fall, causing serious personal injury and serious damage to the product.  
Use only with cart, stand, or table recommended by the manufacturer or sold  
with the product. The combination of the product and stand should be  
moved carefully. Quick movements, excessive force on uneven surfaces may  
overturn the combination which may damage the product and stand  
combination. Follow the manufacturers instructions when installing the  
product and use mounting accessories recommended by the manufacturer.  
13. Unplug this apparatus during lightning storms or when unused for long  
periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is required when  
the apparatus has been damaged in any way, such as when the power-  
supply cord or plug is damaged, liquid has been spilled or objects have fallen  
into the apparatus, the apparatus has been exposed to rain or moisture, does  
not operate normally, or has been dropped.  
15. This unit produces heat when operated normally. Operate in a well-  
ventilated area.  
16. This product, in combination with an amplifier and headphones or speakers,  
may be capable of producing sound levels that could cause permanent  
hearing loss. Do not operate for a long period of time at a high volume level  
or at a level that is uncomfortable. If you experience any hearing loss or  
ringing in the ears, you should consult an audiologist.  
8
DG8 REFERENCE MANUAL  
 
Important Safety Instructions  
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES  
(FRENCH)  
SYMBOLES UTILISÉS DANS CE PRODUIT  
Ce symbole alèrte l’utilisateur qu’il existe des instructions de  
fonctionnement et de maintenance dans la documentation jointe  
avec ce produit.  
Ce symbole avertit l’utilisateur de la présence d’une tension non  
isolée à l’intérieur de l’appareil pouvant engendrer des chocs  
électriques.  
VEUILLEZ SUIVRE CES PRÉCAUTIONS LORS DE  
LUTILISATION DE LAPPAREIL:  
1. Lisez ces instructions.  
2. Gardez ces instructions.  
3. Tenez compte de tous les avertissements.  
4. Suivez toutes les instructions.  
5. N’utilisez pas cet allareil à proximité de l’eau.  
6. Ne nettoyez qu’avec un chiffon humide. Ne pas vaporiser de liquide nettoyant  
sur l’appareil, cela pourrait abîmer les contrôles de la face avant ou engendrer  
des conditions dangeureuses.  
7. Installez selon les recommandations du constructeur.  
8. Ne pas installer à proximilé de sources de chaleur comme radiateurs, cuisinière  
ou autre appareils (don’t les amplificateurs) produisant de la chaleur.  
9. Ne pas enlever la prise de terre du cordon secteur. Une prise murale avec terre  
deux broches et une troisièrme reliée à la terre. Cette dernière est présente pour  
votre sécurité. Si le cordon secteur ne rentre pas dans la prise de courant,  
demandez à un électricien qualifié de remplacer la prise.  
10. Evitez de marcher sur le cordon secteur ou de le pincer, en particulier au niveau  
de la prise, et aux endroits où il sor de l’appareil.  
11. N’utilisez que des accessoires spécifiés par le constructeur.  
12. N’utilisez qu’avec un stand, ou table conçus pour l’utilisation d’audio  
professionnel ou instruments de musique. Dans toute installation, veillez de ne  
rien endommager à cause de câbles qui tirent sur des appareils et leur support.  
13. Débranchez l’appareil lors d’un orage ou lorsqu’il n’est pas utilisé pendant  
longtemps.  
DG8 REFERENCE MANUAL  
9
 
Important Safety Instructions  
14. Faites réparer par un personnel qualifié. Une réparation est nécessaire lorsque  
l’appareil a été endommagé de quelque sorte que ce soit, par exemple losrque le  
cordon secteur ou la prise sont endommagés, si du liquide a coulé ou des objets  
se sont introduits dans l’appareil, si celui-ci a été exposé à la pluie ou à  
l’humidité, ne fonctionne pas normalement ou est tombé.  
15. Cet appareil produit de la chaleur en fonctionnement normal.  
16. Ce produit, utilisé avec un amplificateur et un casque ou des enceintes, est  
capable de produite des niveaux sonores pouvant engendrer une perte  
permanente de l’ouïe. Ne l’utilisez pas pendant longtemps à un niveau sonore  
élevé ou à un niveau non confortable. Si vous remarquez une perte de l’ouïe ou  
un bourdonnement dans les oreilles, consultez un spécialiste.  
10  
DG8 REFERENCE MANUAL  
 
Important Safety Instructions  
BEIM BENUTZEN DIESES PRODUKTES BEACHTEN  
SIE BITTE DIE FOLGENDEN SICHERHEITSHINWEISE:  
(GERMAN)  
1. Lesen Sie die Hinweise.  
2. Halten Sie sich an die Anleitung.  
3. Beachten Sie alle Warnungen.  
4. Beachten Sie alle Hinweise.  
5. Bringen Sie das Gerät nie mit Wasser in Berührung.  
6. Verwenden Sie zur Reinigung nur ein weiches Tuch. Sprühen Sie keine flüssiger  
Reiniger auf die Oberfläche, dies könnte zur Beschädigung der Vorderseite  
führen und auch weitere Schäden verursachen.  
7. Halten Sie sich beim Aufbau des Gerätes an die Angaben des Herstellers.  
8. Stellen Sie das Gerät nich in der Nähe von Heizkörpern, Heizungsklappen oder  
anderen Wärmequellen (einschließlich Verstärkern) auf.  
9. Verlegen Sie das Netzkabel des Gerätes niemals so, daß man darüber stolpern  
kann oder daß es gequetscht wird.  
10. Benutzen Sie nur das vom Hersteller empfohlene Zubehör.  
11. Verwenden Sie ausschließlich Wagen, Ständer, oder Tische, die speziell für  
professionelle Audio- und Musikinstrumente geeignet sind. Achten Sie immer  
darauf, daß die jeweiligen Geräte sicher installiert sind, um Schäden und  
Verletzungen zu vermeiden. Wenn Sie einen Rollwagen benutzen, achten Sie  
darauf, das dieser nicht umkippt, um Verletzungen auszuschließen.  
12. Ziehen Sie während eines Gewitters oder wenn Sie das Gerät über einen  
längeren Zeitraum nicht benutzen den Netzstecher aus der Steckdose.  
13. Die Wartung sollte nur durch qualifiziertes Fachpersonal erfolgen. Die Wartung  
wird notwendig, wenn das Gerät beschädigt wurde oder aber das Stromkabel  
oder der Stecker, Gegenstände oder Flüssigkeit in das Gerät gelangt sind, das  
Gerät dem Regen oder Feuchtigkeit ausgesetzt war und deshalb nicht mehr  
normal arbeitet oder heruntergefallen ist.  
14. Bei normalem Betrieb des Gerätes kommt es zu Wärmeentwicklungen.  
15. Dieses Produkt kann in Verbindung mit einem Verstärker und Kopfhörern oder  
Lautsprechern Lautstärkepegel erzeugen, die anhaltende Gehörschäden  
verursachen. Betreiben Sie es nicht über längere Zeit mit hoher Lautstärke oder  
einem Pegel, der Ihnen unangenehm is. Wenn Sie ein Nachlassen des Gehörs  
oder ein Klingeln in den Ohren feststellen, sollten Sie einen Ohrenarzt aufsuchen.  
DG8 REFERENCE MANUAL  
 
11  
Important Safety Instructions  
INSTRUCTIONS TO THE USER  
This equipment has been tested and found to comply with the limits for a class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try and correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This equipment has been verified to comply with the limits for a class B computing  
device, pursuant to FCC Rules. In order to maintain compliance with FCC  
regulations, shielded cables must be used with this equipment. Operation with non-  
approved equipment or unshielded cables is likely to result in interference to radio  
and TV reception. The user is cautioned that changes and modifications made to the  
equipment without the approval of manufacturer could void the user’s authority to  
operate this equipment.  
12  
DG8 REFERENCE MANUAL  
 
Important Safety Instructions  
CE DECLARATION OF CONFORMITY  
Manufacturer’s Name:  
Alesis Corporation  
Manufacturer’s Address:  
1633 26th Street  
Santa Monica, CA 90404  
USA  
declares, that the product:  
Product Name:  
Model Type:  
DG8  
Digital Grand Piano  
conforms to the following Standards:  
EMC:  
EN55103: 1997 Class B  
EN 60065  
Safety:  
European Contact:  
Sound Technology  
17 Letchworth Point, Letchworth,  
Hertfordshire, SG6 1ND, England.  
Phone: +44.1462.480000  
Fax: +44.1462.480800  
June, 1999  
DG8 REFERENCE MANUAL  
13  
 
Important Safety Instructions  
14  
DG8 REFERENCE MANUAL  
 
Introduction  
INTRODUCTION  
In the years since electronic musical instruments made their debut in the early 1970s,  
the quest for a transportable piano that had the sound and feel of a true acoustic  
instrument seemed to elude every manufacturer. They tried everything, including a  
rather ingenious re-design of the grand piano that you could take apart into two  
pieces when travelling. The trade-off? It was still bulky, rather expensive, and  
because it had strings (just like a real piano) it needed to be tuned periodically. If you  
moved it often, you had to tune it often.  
Even as digital sampling technology began to mature in the early 1990s and piano  
products started popping up all over, something always seemed to be missing: the  
sound was thin or the keys didn’t feel right or the pedals didn’t respond like you’d  
expect or... well, you get the point.  
But no matter how big my music rig gets – no matter how many gadgets and boxes  
and toys I accumulate – the one sound that I have always insisted upon is a great  
piano. The Alesis DG8 is a great piano. And more.  
The DG8 sounds like a piano and feels like a piano. Its 88-key, fully-weighted,  
hammer-action keyboard is an advanced design that provides the response you’d  
expect from, well, a real piano. Complementing its piano realism are four pedal  
inputs: sustain/sostenuto and soft pedal expression plus an AUX jack for  
volume/modulation. Factor in the DG8’s 64-voice polyphony, and you have an  
instrument that faithfully reproduces all the nuances of a fine acoustic piano.  
But we wouldn’t be satisfied with just a standard piano. We’ve tailored our selection  
of pianos to be ideally suited for classical, jazz, rock and pop, and included an entire  
suite of electric pianos, pipe and electric organs, synthesizers, strings, choirs, basses,  
clavinets, vibes and harpsichord. In addition to its 88 preset programs, the DG8’s  
24MB of sound ROM is expandable to 32MB via a PCMCIA expansion card slot,  
TM  
ideally suited for any Alesis QCard expansion module.  
The DG8’s velocity-sensitive keyboard can be layered and split, of course. The split  
point can be set to any point on the keyboard you want, and the Transpose feature  
puts the DG8 into any key.  
And to further enhance the DG8’s sound capability, the Alesis QS Parallel Matrix  
TM  
Effects provide reverb and chorus on nearly all internal Keyboard Programs (the  
electric organ programs substitute a rotary speaker effect for chorus). Add to that a  
5-band analog graphic equalizer and a built-in 100-watt-per-channel, discrete stereo  
bi-amped amplifier and speakers, and the DG8 is a fully-integrated powerhouse  
instrument.  
We’ve just touched on the some of the highlights of this product; there’s much more  
to be explored. After you’ve read through this brief document, and experienced the  
sound and feel of the DG8, I’m confident that you will be every bit as excited about it  
as I am.  
Dave Bertovic  
Spring 1999  
DG8 REFERENCE MANUAL  
 
15  
Introduction  
TYPOGRAPHIC CONVENTIONS  
In this manual, we attempt to make the reading as easy as possible by using fonts  
and symbols that are easy to identify. The following list describes the conventions we  
use in the manual for special or important information.  
Slider, button and back panel labels are in SMALL BOLD CAPITALS.  
Words or phrases that appear in the display are printed using type that  
resembles the display characters.  
A new or important term is in italics followed by its definition or contextual meaning.  
Paragraphs in italics provide additional information on a topic that might be helpful in  
understanding certain important concepts.  
Tip: A hint or special example called a Tip is set off from the main text by a box with  
a light-gray fill.  
Important instructions or emphasis on a word or phrase are printed in boldface  
type.  
When something extremely important appears in the manual, an  
icon like the one on the left will appear in the left margin. This  
indicates that this information is vital when operating the DG8.  
16  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
CHAPTER 1  
GETTING STARTED  
WHAT YOULL NEED  
The DG8 is a completely self-contained instrument that needs nothing more than a  
standard AC electrical outlet and a stand to put it on. Before placing the DG8 on a  
stand, see the topic Set It Up at the bottom of this page for specifics.  
USING THE DG8 WITH OTHER EQUIPMENT  
If you plan to use the DG8 with other equipment, such as other MIDI devices, a  
sound system or in recording environment, you’ll need:  
1. Standard MIDI cables that connect your DG8 to other MIDI devices in your  
system. See the topic Hook It Up on page 19 for more information.  
2. A standard AC outlet where you can plug the unit in.  
3. A basic working knowledge of MIDI. If you’re new to all of this, read our  
brief MIDI tutorial in Chapter 3.  
4. Audio cables to connect your DG8 to a sound system.  
UNPACK IT  
The DG8 is packaged in a cardboard container with molded styrofoam inserts. After  
you remove your DG8, its AC power cord, the Warranty card and this manual, we  
suggest you keep all packing materials in a safe place. You’ll need the box and  
styrofoam in case the unit needs to be transported or shipped.  
SET IT UP  
You can place the DG8 just about anywhere that’s convenient. For tips on setting up  
the DG8 in your home, see the topic on page 19.  
Before placing the DG8 on a stand, be certain that is capable of securely holding an  
object that weighs 80 lbs. (36.3kg). Also take in to consideration how aggressive a  
player you are: the harder you pound the keys, the stronger a stand you’ll need. If  
the stand collapses under the DG8’s weight (or your playing), the unit could suffer  
permanent damage, and you could be injured. Don’t take chances; take the time right  
now to make sure that your stand is adequate.  
You might also want to consider the optional Alesis GS-1 Digital Piano stand. This  
attractive accessory is ideal for the home or studio where the DG8 has a permanent  
place of residence.  
DG8 REFERENCE MANUAL  
 
17  
Chapter 1: Getting Started  
ATTACHING THE MUSIC STAND  
The DG8 is shipped with a music stand that attaches easily to the top of the  
instrument:  
1. Remove the music stand from its plastic wrapping and extend the braces  
away from the front of the stand approximately 5 - 6 inches. The braces swing  
out from the front of the stand on a pair of hinges.  
2. Insert the ends of the braces into the two mounting holes located along the  
rear edge of the DG8’s top.  
3. You can adjust the angle of the stand once it is in place. Grip the front of the  
stand at the bottom corners and gently pull towards you or push away from  
you to adjust the angle.  
PUSH or PULL THE  
STAND FROM HERE  
18  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
SETTING UP THE DG8 IN A HOME  
Placement of your DG8 in the room can have a great effect on its overall tonal  
balance. Placing the DG8 is like placing loudspeakers in a room – placing the unit  
right up against a wall will accentuate the bass and if the wall has thick draperies,  
they will also cut the treble producing a dark, boomy sound.  
The most accurate sound is usually achieved when the DG8 is placed on an  
appropriate stand and positioned out and away from highly reflective or highly  
absorptive wall surfaces. But when the DG8 must be situated close to a wall, as in a  
home, here are some recommendations:  
If the wall is hard and smooth (a “reflective” surface), try positioning the  
keyboard at least 6” away. Too close and the tweeter frequencies will bounce  
back at you and cause a blurred and “splashy” high frequency effect. Also in  
this position, the wall may give a “boomy” character to the lower octaves. This  
is called bass coupling where bass sounds get a boost from the nearby wall.  
If the nearby wall is curtained or otherwise presents a highly absorptive  
environment, the DG8 should be positioned out at least 12”. As mentioned  
earlier, thick draperies will cut treble and the result will be a dark, muffled  
sound.  
HOOK IT UP  
POWER  
Use the AC power cord (or equivalent) that is included with the DG8. Make sure that  
the unit is turned off before you plug the power cord into the rear panel receptacle  
and the wall outlet. The unit has a universal power supply that should work with  
local AC power in most countries. If in doubt, check with your power company  
before plugging it in. In the U.S., the DG8 must be plugged into a standard 117 VAC,  
50 - 60 Hz outlet.  
SUSTAIN PEDAL  
Before powering on the DG8, plug the included sustain pedal into the SUSTAIN/SOST  
jack on the back panel.  
THE DG8 AS A STAND-ALONE INSTRUMENT  
After you’ve set up the DG8 and plugged it into an AC outlet, you can go right ahead  
and dig in. If you plan to play the DG8 by itself, skip ahead to the topic Turn It On  
and Play It on page 23.  
If you plan to use the DG8 with other MIDI instruments and devices in a music  
system, use the examples on the next few pages to connect it to your rig.  
DG8 REFERENCE MANUAL  
 
19  
Chapter 1: Getting Started  
THE DG8 IN A MUSIC SYSTEM  
If you plan to use the DG8 with other MIDI instruments and devices in a music  
system, you’ll need to integrate it into your system. Here’s a list of items you’re likely  
to need:  
1. standard MIDI cables: refer to the following examples for possible  
connection schemes.  
2. a basic working knowledge of MIDI. If you’re new to all of this, read our  
brief MIDI tutorial in Chapter 3.  
3. two 2-conductor (unbalanced) audio cables if you plan to route the DG8’s  
audio to your sound system or audio mixer.  
As a Master:  
If you intend to use the DG8 as the master controller in your  
MIDI rig, plug a standard MIDI cable into the DG8’s MIDI OUT  
port. The other end of this cable should plug into the MIDI IN of  
the first slave in the system. If there are several MIDI  
instruments in your setup, connect MIDI THRU from the first slave  
to the MIDI IN of the second device and so forth to create a  
“chain”.  
POWER  
VALUE  
EDIT MODE  
CURSOR  
PLAY MODE  
64 VOICE EXPANDABLE SYNTHESIZER MODULE  
EDIT  
MIX  
PROG  
A
B
MIDI CH  
STORE  
DOWN  
COMPARE  
UP  
GLOBAL  
MIDI CHANNEL  
PHONES  
VOLUME  
PCMCIA EXPANSION CARDS  
BANK SELECT  
20  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
As a Slave:  
If you plan to control the DG8 from another MIDI device, you’ll  
need a MIDI cable connected to its MIDI IN port.  
You will also need a MIDI cable connected to the DG8’s MIDI  
THRU if you plan to pass MIDI data from the master through the  
DG8 to other MIDI devices in your rig. Connect one end of a  
MIDI cable to the DG8’s MIDI THRU. Plug the other end of the  
cable to the MIDI IN of the next device in the system.  
POWER  
VALUE  
EDIT MODE  
CURSOR  
PLAY MODE  
64 VOICE EXPANDABLE SYNTHESIZER MODULE  
EDIT  
MIX  
PROG  
A
B
MIDI CH  
STORE  
DOWN  
COMPARE  
UP  
GLOBAL  
MIDI CHANNEL  
PHONES  
VOLUME  
PCMCIA EXPANSION CARDS  
BANK SELECT  
DG8 REFERENCE MANUAL  
21  
 
Chapter 1: Getting Started  
With a MIDI Patchbay:  
If you’re using a MIDI patchbay or “patcher” to connect all of  
your MIDI devices centrally, it’s likely that the patcher’s back  
panel will have a series of paired MIDI OUT and MIDI IN ports for  
each device in your rig (the DG8 being one of them).  
Connect the DG8’s MIDI OUT to the MIDI IN of one of the pairs. The  
same pair’s MIDI OUT connects to the MIDI IN of the DG8. Consult  
the patcher’s Owner’s Manual to find out how it routes MIDI  
data among the devices connected to it.  
VALUE  
EDIT MODE  
CURSOR  
PLAY MODE  
POWER  
64 VOICE EXPANDABLE SYNTHESIZER MODULE  
EDIT  
MIX  
PROG  
A
B
MIDI CH  
STORE  
DOWN  
COMPARE  
UP  
GLOBAL  
MIDI CHANNEL  
PHONES  
VOLUME  
PCMCIA EXPANSION CARDS  
BANK SELECT  
22  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
TURN IT ON AND PLAY IT  
Flip the power switch on the DG8’s rear panel. The front panel display will  
illuminate and, if this is the first time you’ve used the DG8, it will recall  
Keyboard Program Pno1A:True Grandand display it under the PRIMARY  
SOUND heading.  
1. AutoDemos  
Press and hold the PLAY button, then press the TUNE button to enter Demo  
mode. The display will prompt you to select one of three demonstration songs  
to play by pressing the PIANO 1, PIANO 2 or PIANO 3 Bank buttons. You can  
listen to any demo in its entirety, or press the PLAY button to end a demo that  
is playing.  
HOW THE SOUNDS ARE ORGANIZED  
2. Keyboard Banks  
The Keyboard Banks contain the main polyphonic sound programs in the  
DG8’s internal memory.  
Each of the 15 Keyboard Banks contains four Keyboard Programs. Thus, each  
Bank represents a sound category – a group of related sounds – and the name  
of the category is printed on each button.  
The Keyboard Bank buttons are used in conjunction with the and arrows  
to access the Keyboard Programs in each Bank:  
Press a Keyboard Bank button to select a Keyboard category. The name  
of a Keyboard Program from the selected Bank will appear in the  
PRIMARY SOUND segment of the display.  
Use the arrow on the right side of the display to scroll forward through  
the four Keyboard Programs in the Bank. If you continue to scroll  
forward with the arrow, when the last Program in the bank is reached,  
the display will “wrap” to the first Program.  
Use the arrow to scroll backward through the four Keyboard Programs  
in each Bank. If you continue to scroll backward with the arrow, when  
the first Program in the Bank is reached, the display will wrap to the last  
Program.  
Keyboard Programs can be played by themselves, layered together (or  
layered with a Card Program) or split with a Bass or Card Program. See topics  
4, 5 and 6 on the next few pages for information on these Play modes.  
3. Bass Banks  
Similar to the Keyboard Banks, the Bass Banks contain the main bass sound  
programs in the DG8’s internal memory. And, like the Keyboard Banks, each  
of the seven Bass Banks contains four Bass Programs. Each Bank represents a  
category of related bass sounds and the name of the category is printed on  
each button.  
Note that the DG8’s internal Bass Programs are programmed without  
modulation – they will not respond to the modulation setting for the AUX  
pedal, nor modulation commands received over MIDI. Also, there is a  
minimal amount of Reverb and Chorus effects programmed into the Bass  
Programs.  
DG8 REFERENCE MANUAL  
 
23  
Chapter 1: Getting Started  
The Bass Bank buttons are used in conjunction with the and arrows to  
access the Bass Programs in each Bank:  
Press a Bass Bank button to select a Bass category. Bass Programs are  
always played as the Split sounds on the lower range of the keyboard,  
and the selected Bass Program’s label will appear in the SPLIT segment  
of the display.  
Use the arrow on the right side of the display to scroll forward through  
the four Bass Programs in the Bank. If you continue to scroll forward  
with the arrow, when the last Program in the bank is reached, the  
display will “wrap” to the first Program.  
Use the arrow to scroll backward through the four Bass Programs in  
each Bank. If you continue to scroll backward with the arrow, when  
the first Program in the Bank is reached, the display will wrap to the last  
Program.  
4. The Card Bank  
You can take advantage of the DG8’s expandability by acquiring an Alesis  
QCard or other compatible PCMCIA Type I sound card. This card provides  
an additional library of new sounds you can play on the DG8 and is inserted  
into the EXPANSION CARD slot on the DG8’s back panel.  
Once selected, these external sounds act just like the internal DG8  
programs, except that there are 128 of them on a QCard. Press the CARD  
button: the last card sound that was selected will load and its name will  
appear in the display.  
Tip: Card sounds can be used in Layers and Splits. They can be combined with the  
DG8’s internal sounds or can be layered and split among the other programs in  
the Card Bank. See topics 6 and 7 in the following pages.  
Use the arrow on the right side of the display to scroll forward through  
the Card Programs. If you continue to forward scroll with the arrow,  
when the last Program in the bank is reached, the display will “wrap” to  
the first Program.  
Use the arrow to scroll backward through the card programs. If you  
continue to scroll backward with the arrow, when the first Program in  
the Bank is reached, the display will wrap to the last Program.  
Tip: If you press and hold either arrow button, the display will accelerate its  
scrolling through the available programs. Also, pressing both arrows together  
resets the Card Program to 000.  
Do not physically remove the card from the rear slot while any Card  
Program is active. This holds true for Primary, Layer or Split sounds.  
If a Card Program is the Primary Sound, simply switch the Card  
Program to an internal Keyboard Program. If a Card Program is the  
Layer or Split Sound, simply turn off the Layer or Split.  
Also note that the effects programmed into QCard sounds may act  
unpredictably when used with the DG8.  
24  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
HOW THE SOUNDS ARE SELECTED  
5. Single Mode  
The DG8 is in Single mode when a Keyboard or Card Program is played alone  
– the DG8 is not in a Layer or Split. The Program’s name and label appears in  
the top line of the display under the PRIMARY SOUND heading. The Keyboard  
or Card Program that is displayed here will be appropriately called the  
Primary sound or simply “the Primary” throughout the manual.  
The important concept to understand here is that a Primary sound is  
always active, whether it is an internal Keyboard Program or a Card  
Program.  
With this principle in mind, you can think of a Layer as “adding another  
Keyboard or Card Program to be played on top of the current Primary”.  
Likewise, a Split is created when “a Bass or Card Program is played on the  
lower range of keys with the Primary on the upper range”. The Layer and  
Split play modes are described in the following two topics:  
6. Layers  
A Layer is simply two Keyboard or Card Programs (or one of each) stacked  
one on top of the other. Selecting a Layer causes the keys to play the two  
Programs simultaneously. There are two methods you can use to create a  
Layer:  
Press and hold the LAYER/OFF button then press a Keyboard Bank button  
or the CARD button. The current Program in the PRIMARY display will be  
layered with a second Keyboard Program (or a Card Program) that  
appears in the LAYER segment of the display.  
OR  
Press a Keyboard Bank button to select the Primary sound. While you  
are still pressing the Keyboard Bank button, press another Keyboard  
Bank or the CARD button to select the Layer sound.  
In either case, use the and arrows, if necessary, to select the desired  
Keyboard Program or Card Program of the LAYER sound.  
Variations:  
You can layer two Programs from the same Keyboard Bank. After  
selecting the desired Primary program, press and hold the LAYER/OFF  
button and press the same Keyboard Bank button. Use the and ▼  
arrows to select the desired Keyboard Program in that Bank. Please note  
that this method is the only way you can layer two Keyboard Programs  
from the same Bank.  
If a Card Program is the Primary, pressing and holding LAYER/OFF then  
pressing CARD causes two Card Programs to be layered. Please note that  
this method – using the LAYER/OFF button to create the Layer – is the only  
way you can layer two Card Programs.  
Use the LAYER LEVEL slider to adjust the volume of the LAYER sound  
relative to the PRIMARY.  
To exit this mode, press the LAYER/OFF button.  
DG8 REFERENCE MANUAL  
 
25  
Chapter 1: Getting Started  
7. Splits  
A Split is simply a Bass or Card Program played on the lower range of keys  
with a Primary sound played from the upper range. (Remember that the  
Primary can be selected from the Keyboard Banks or the Card Bank.)  
To set up a Split, press any Bass Bank button. To select a Card Program  
as the split sound, press and hold SPLIT/OFF then press CARD. Use the ▲  
and arrows to select the desired Split sound from within the selected  
Bass Bank or the Card Bank.  
In either case, the Bass Program or Card Program will be recalled from  
memory as the sound on the lower (left-hand) range of keys and its label  
will appear in the SPLIT segment of the display.  
The default split-point is key “C2”, the C that is one octave below Middle  
C. To change the split point, press the SET SPLIT button. The display will  
prompt you to press a key on the DG8’s keyboard. This key will be the  
highest note of the lower range.  
Note that if you don’t press a key within two seconds, the display will  
revert back to the program display, leaving the current split point  
unchanged.  
To change the lower sound, use the and arrows to select another  
program in the current Bass Bank or Card Bank, or press another Bass  
Bank button.  
To change the upper sound, press another Keyboard Bank button; to  
switch the upper sound to the Card Bank, press CARD. Use the and ▼  
arrows to select the desired Program in the Keyboard/Card Banks.  
To exit this mode, press the SPLIT/OFF button.  
8. Split-with-Layer  
When the DG8 is playing a Split: press and hold the LAYER/OFF button and  
press another Keyboard Bank button or the Card Button to add a LAYER  
sound to the upper range of the keyboard.  
If the DG8 is playing a Layer: press any Bass Bank button to split the layered  
keyboard with an internal Bass Program on the lower range of the keyboard.  
To split a layered keyboard with a Card Program, press and hold SPLIT/OFF  
and press CARD.  
Tip: For Primaries, Layers and Splits, the DG8’s memory independently keeps track  
of the most recently selected programs for each Bank button. This principle is  
true for the Keyboard, Bass and Card Banks.  
26  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
9. Using the Cursor and the and Arrows  
When interacting with the display, the sound that is underlined by the  
cursor is the one that will be affected by the and arrows. You can always  
keep track of where the cursor is because during normal operation, the last  
sound that you select has the cursor. But if necessary, you can move the  
cursor to another active segment of the display by pressing the PLAY button.  
Repeated pressing of the PLAY button moves the cursor among the active  
fields in the display. Just keep in mind that you can’t move the cursor to a  
blank field. For example, in a Layer, the cursor will only move between the  
PRIMARY and the LAYER sounds. In a Split, the cursor will only move between  
the PRIMARY and the SPLIT sounds. In a Split-with-Layer, the cursor will move  
among all three PRIMARY, SPLIT and LAYER sounds.  
Tip: You can perform a quick reset when certain parameters are being displayed.  
Pressing the and arrows together will reset the following parameters:  
SET SPLIT  
TRANSPOSE  
split point resets to C2  
transpose value resets to Middle C  
Master Tune resets to 00  
resets to 50  
TUNE  
MIDI Page 4: KeyboardScaling  
When the display is in its normal mode of displaying selected Sound Programs,  
pressing the and arrows together will reset Keyboard Bank and Bass Bank  
programs to “A”. Card Bank programs reset to 000.  
USING THE CONTROLS  
10. Level Controls  
Raise or lower the VOLUME slider to adjust the output level to a comfortable  
listening volume. The VOLUME slider adjusts the overall level for everything:  
Primary sounds, Layers, Splits and Effects. But you can also use the LEVEL  
sliders to make further adjustments to the sound balance:  
Adjusting the LAYER slider changes the output of the Layer sound  
relative to the Primary sound. The output level of the Primary Sound  
stays constant when playing a Layer.  
Adjusting the SPLIT slider changes the output of the Bass Program or the  
Card Program assigned to the lower keyboard range relative to the  
Primary. The output level of the Primary Sound stays constant when  
playing a Split.  
Reverb and Chorus have been pre-programmed in nearly all of the  
sounds. You can raise or lower the amount of effects with the REVERB  
and CHORUS sliders.  
The exception to this is the ELECTRIC ORGAN Bank which substitutes a  
rotating speaker effect instead of chorus. The CHORUS LEVEL slider acts as  
a speed control for the rotating speaker.  
Remember also that the DG8’s built-in speakers can be turned off by  
using the SPEAKER ON/OFF switch on the back panel.  
DG8 REFERENCE MANUAL  
 
27  
Chapter 1: Getting Started  
11. Transpose  
You can transpose the DG8 ± 1 octave. Using Middle C (key “C3”) as your  
reference, press and hold the TRANSPOSE button and press a key on the  
keyboard. Pressing a key above Middle C will transpose the DG8 up by the  
interval and pressing a key below Middle C will transpose the DG8 down by  
that interval.  
The selected key will be the new key for the DG8 in any Play mode (Primary,  
Layer, Split or Split-with-Layer) until the transpose amount is changed or the  
instrument is initialized.  
Also, if you attempt a transpose value more than the one octave limit, the  
DG8 will keep the pitch the same but the key selected will be the nearest one  
within the one octave range. For example, if you try to transpose up to key E5  
(the highest E on the keyboard), the DG8 will transpose the keyboard up to  
E3, the E above C3 (Middle C). Also, transposing the keyboard will not affect  
the Split Point’s physical location on the keyboard.  
The Transpose display will exit as soon as you press a key on the DG8’s  
keyboard. To exit this mode without transposing, press PLAY.  
12. TUNE Button  
Page 1: Master Tune  
The DG8 can be tuned to other instruments, a tuning device or your CD  
player, cassette player, etc. Press the TUNE button and use the button to raise  
the pitch of the DG8 and the button to lower it. The range is ± 1 half step,  
and each press of an arrow key changes the tuning by 1 cent (100 cents = 1  
half step) up or down.  
Pressing both and arrows together resets Master Tune to 00.  
To exit this mode, press the PLAY button.  
Page 2: Stretch Tuning  
Pressing the TUNE button a second time enters Stretch Tuning mode which  
employs the tuning method that is actually used to tune real acoustic pianos.  
With Stretch Tuning, the low strings are tuned increasingly flat, and the high  
strings are tuned increasingly sharp compared to the equally-tempered scale.  
This function defaults to ON, and is only active on the three piano groups  
PIANO 1, PIANO 2 and PIANO 3. This feature of the DG8 was not just designed as  
an esoteric function, but provides an unusual level of realism to the piano  
Programs.  
While this mode is desirable when playing a piano program alone, it can  
cause problems when used with Layers or other MIDI instruments. To  
partially avert this, the DG8 automatically turns off this function when you  
enter Layer mode so as to avoid tuning conflicts with other internal DG8  
Programs. However, when playing the DG8 with other instruments via MIDI,  
you may need to defeat Stretch Tuning because the high and low ends of the  
DG8 may sound out of tune with other MIDI instruments. Use the arrow to  
turn this function OFF. When Stretch Tuning is off, the piano programs will  
always be tuned to the equally-tempered scale whether used as a Primary  
Program or as a Layer.  
Note that, like other settings in the DG8, if turning Stretch Tuning is set to OFF  
it will remain off until you change it or re-initialize the instrument.  
To exit this mode, press the PLAY button.  
28  
DG8 REFERENCE MANUAL  
 
Chapter 1: Getting Started  
13. Graphic EQ  
The 5-band analog graphic equalizer on the left side of the control panel  
allows you to make tonal adjustments to the sound. Press the EQ ON/OFF  
button (its LED will light) to activate the equalizer and raise or lower the  
frequency sliders to adjust the tone. Every time you power on the DG8, the  
EQ will be off.  
The equalizer affects the final output of the DG8 for all Primary, Layer and  
Split setups for both internal and Card Programs. The equalizer also affects  
Reverb and Chorus, the inputs and all outputs: the rear panel audio outs plus  
the two headphone jacks.  
14. MIDI Channel Function  
The MIDI button accesses the six MIDI functions of the DG8. For this section of  
manual, we will cover only the Channel function. For a complete description  
of the other MIDI Functions, turn to page 46.  
Pressing the MIDI button will step between six different pages of MIDI and  
other utility functions. Press the MIDI button until the display reads:  
BASIC  
MIDI Channel = X  
... where Xis one of the 16 MIDI Channels or Off. When set to Off, the DG8  
will neither transmit nor receive MIDI information.  
Use the and arrows to select the new Basic MIDI Channel, or Off. To  
confirm your selection and exit this mode, press PLAY.  
How the Basic MIDI Channel Works on the DG8  
When you first power on the DG8, the Basic Channel defaults to Channel 1.  
So that the DG8 will communicate effectively with other MIDI devices, the  
DG8 treats Primary Sounds, Layers and Splits differently:  
The MIDI Channel displayed is the Basic Channel for all messages  
affecting Primary Sounds. In addition, the Basic MIDI Channel affects all  
messages for the Layer sound, except Program Change commands.  
The MIDI Channel assignment for just the Layer Program Changes  
follows sequentially: Layer Program Changes = Basic Channel + 1.  
The MIDI Channel assignment for all messages for Splits again follows  
sequentially: Splits = Basic Channel + 2.  
Here’s a summary of these functions using the MIDI Channel default as an  
example:  
MIDI Channel 1 Primary Sounds  
Layer Programs  
all supported Channel Messages  
all supported Channel Messages except  
Program Change commands  
MIDI Channel 2 Program Change commands (only) for the Layer sound  
MIDI Channel 3 Split Programs  
all supported Channel Messages  
Program Change commands only affect  
the Bass Program.  
DG8 REFERENCE MANUAL  
 
29  
Chapter 1: Getting Started  
30  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
CHAPTER 2  
PLAYING THE DG8  
OVERVIEW  
The DG8 contains a total of 88 sound programs in its internal memory. 60 of these are  
called Keyboard Programs and represent a selection of pianos and other keyboard  
instruments such as harpsichord, electric piano, clavinet, pipe and electric organs. In  
addition, popular electronic keyboard sounds such as traditional synthesizer and  
“pad” sounds, strings (orchestral or ensemble type), choir and vibes are included.  
For Splits – where the DG8 plays a sound on the lower range and another sound on  
the upper range of the keyboard – a selection of 28 popular Bass Programs are  
included for left hand accompaniment on the lower keyboard range.  
Each of the DG8’s sound programs is a digital sample – an electronic recording of an  
audible sound – that is stored in the instrument’s memory. The DG8’s memory is a  
type of memory used in a wide variety of electronic instruments and computers  
called ROM (“Read-Only Memory”) which cannot be erased or altered.  
Sound programs in the DG8 may be constructed of only one instrument or, as in the  
case of PAD, SYNTH or MULTI sounds (to name a few), a composite sound.  
A composite sound is a sound that was constructed from one or more synthesizers and/or  
samplers. When playing one of these DG8 sounds, you may hear what appears to be several  
sounds mixed together. In this case, that’s exactly what we did. The resulting program in the  
DG8 is a rich and full sound, but only takes up a single location in memory.  
HOW THE SOUNDS ARE ORGANIZED  
The DG8 divides its sound memory into two categories, internal and external  
sounds. Internal sounds are accessed from the Keyboard Banks and the Bass Banks.  
External sounds are called Card Bank programs and are accessed from a sound card  
inserted in the back panel’s EXPANSION CARD slot.  
Keyboard Banks  
The DG8 has 60 Keyboard Programs in its internal memory. These 60 sounds are  
arranged into 15 Banks that correspond to the 15 rectangular buttons on the right  
side of the control panel.  
Each Bank contains four variations of the sound that is printed on the button label.  
For example, FM PIANO contains four well-known FM-type electronic piano sounds;  
PIPE ORGAN contains four variations of pipe organ ensembles usually associated with  
church or cathedral organs.  
DG8 REFERENCE MANUAL  
 
31  
Chapter 2: Playing the DG8  
The Keyboard Bank buttons are used in conjunction with the and arrows to  
access the Keyboard Programs in each Bank:  
Press a Keyboard Bank button to select a Keyboard category. The name and  
label of a Keyboard Program from the selected Bank will appear in the PRIMARY  
SOUND segment of the display.  
Use the arrow on the right side of the display to scroll forward through the  
four Keyboard Programs in the Bank. If you continue to scroll forward with  
the arrow, when the last Program in the bank is reached, the display will  
“wrap” to the first Program.  
Use the arrow to scroll backward through the four Keyboard Programs in  
each Bank. If you continue to scroll backward with the arrow, when the first  
Program in the Bank is reached, the display will wrap to the last Program.  
A Keyboard Program can be played by itself as single program, layered with another  
Keyboard Program or Card Program, or split with a Bass (or Card) Program. See the  
topics on Layers and Splits starting on page 36 for information on these Play Modes.  
Bass Banks  
Similar to the Keyboard Banks, the Bass Banks contain the main bass sound  
programs in the DG8’s internal memory. And, like the Keyboard Banks, each of the  
seven Bass Banks contains four Bass Programs. Each Bank represents a category of  
related bass sounds and the name of the category is printed on each button.  
Note that the DG8’s internal Bass Programs are programmed without modulation –  
they will not respond to a mod pedal plugged into its back panel or to received MIDI  
modulation commands. Also, there is a minimal amount of Reverb and Chorus  
effects programmed into the Bass Programs.  
The Bass Bank buttons are used in conjunction with the and arrows to access the  
Bass Programs in each Bank:  
Press a Bass Bank button to select a Bass category. Bass Programs are always played  
as the Split sounds on the lower range of keys, and the selected Bass Program’s  
label will appear in the SPLIT segment of the display.  
Use the and arrows to step forward or backward through the four Bass Programs  
in the Bank.  
The Card Bank  
You can take advantage of the DG8’s expandability by acquiring an Alesis QCard or  
other compatible PCMCIA Type I sound card. The QCard provides an additional  
library of 128 new sounds you can play on the DG8. Just be aware that the effects  
programmed into each card sound may act unpredictably.  
The card’s sounds act just like the internal DG8 programs. You can use Card  
Programs for Primaries, Layers and Splits by pressing the CARD button instead of a  
Bank button when selecting a sound. The last card sound that was selected will load  
and its name and/or label will appear in the appropriate segment of the display. Use  
the and arrows to step forward or backward through the Card Programs in the  
Card Bank to select another program.  
Card sounds can be combined with the DG8’s internal sounds or can be layered  
and/or split within the Card Bank. A complete tutorial on using Card Programs is  
provided in the section Using the External Card Sounds starting on page 40.  
32  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
USING THE DISPLAY AND SOUND SELECTION BUTTONS  
In Play mode, the display shows the name(s) of the selected sound(s) – all three if a  
Split-with-Layer is selected. The most recently selected sound is underlined by the  
cursor. In our first example, a Split-with-Layer is shown:  
In this next example, an internal Primary Sound is layered with an optional external  
Card Program. Notice that the Split display segment is blank indicating that Split  
keyboard mode is not active:  
How Sound Programs are Named  
Primary Sounds are displayed with a 10-character name and a 5-character label – a  
combination of the name of the Bank Button plus A, B, Cor Drepresenting the four  
sound variations in each Keyboard Bank. Card Programs substitute a 3-digit number  
for the A, B, Cor Dbecause each Alesis QCard has 128 sound programs.  
Layer and Split sound programs use only labels in the display. For the complete list  
of DG8 sound labels, see the DG8 Sound Chart on page 43.  
Using the Cursor and the and Arrows  
When interacting with the display, one of the key concepts is to keep track of where  
the cursor is located. Notice in the first diagram above that the cursor is an underline  
of the first character in the Program Label. The sound that is underlined by the  
cursor is the one that will be affected by the and arrows. Keeping track of the  
cursor will not be an issue when playing Primary Sounds only, or if you’re in the  
process of setting up a Layer or Split. But it will be a real time-saver when you’re  
selecting new sounds for an existing Layer, Split or Split-with-Layer.  
To move the cursor when a Layer, Split or Split-with-Layer is active, press the PLAY  
button. Repeated presses of the PLAY button move the cursor around the display.  
When the cursor is at the LAYER sound, for example, pressing the and arrows will  
DG8 REFERENCE MANUAL  
 
33  
Chapter 2: Playing the DG8  
select another Program within the current Keyboard or Card Bank for the Layer  
sound. When the cursor is at the SPLIT sound, pressing the and arrows will select  
another Program within the current Bass Bank or Card Bank for the Split sound.  
A complete tutorial on using the and arrows and cursor to select sound  
programs and setting up Layers and Splits is provided in the section Selecting  
Internal Sounds on the next page.  
Other and Arrow Functions  
The and arrows are also used to select parameters and change numeric values in  
the TUNE and MIDI modes.  
Acceleration  
Note that when selecting Programs and changing numeric values in the display,  
pressing and holding an arrow will accelerate the scrolling. This is most noticeable  
(and most handy) when selecting Card Sounds. Because there are 128 sounds on an  
Alesis QCard, this feature is another time-saver.  
Display Wrap  
Also, when selecting Programs (internal or card), pressing an arrow repeatedly (or  
holding it down) will wrap the display: pressing or holding the button when  
selecting any internal sound will display all four sounds in that Bank in succession.  
When the fourth sound is reached, continued pressing of the button will wrap the  
display to the first sound in the Bank and continue on. By the same token, scrolling  
backward with the arrow wraps the display back to the fourth sound after the first  
sound is reached.  
Wrapping is also especially handy with Card Sounds as it solves the problem of  
scrolling through 128 programs just to get to the first (or last) sound on the card.  
Wrapping also occurs when selecting MIDI Channels.  
Reset  
The last feature of the arrows is the Reset function. When selecting numeric values  
for Master Tune or Keyboard Scaling, for example, pressing both arrows  
simultaneously resets the function to its default value, which is usually 0 or a value  
that represents a mid-point in the function’s range. When displayed, pressing the ▲  
and arrows together will reset the following parameters:  
SET SPLIT  
TRANSPOSE  
TUNE  
split point resets to C2  
transpose value resets to Middle C  
Master Tune resets to 00  
resets to 50  
MIDI Page 4: KeyboardScaling  
When the display is in its normal mode of displaying selected Programs, pressing the  
and arrows together will reset Keyboard Bank or Bass Bank programs to "A".  
Card Bank programs reset to 000. When resetting a displayed Program, move the  
cursor to the sound you want to reset with the PLAY button.  
34  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
SELECTING INTERNAL SOUNDS  
The DG8’s internal sounds can be selected and arranged in any of four Play Modes or  
keyboard setups: Single, Layer, Split and Split-with-Layer.  
To make things a little more interesting – and flexible – these modes can also be used  
with an external set of sounds provided on an optional PCMCIA Type I-compatible  
ROM card such as an Alesis QCard. This Card Bank contains additional sounds that  
can be played as Primary sounds but can also be played in a Layer, Split or Split-  
with-Layer. Things really get interesting when you combine internal programs with  
the external sounds on the QCard.  
But for now, we will limit our discussion of selecting sounds and creating Layers  
and Splits to the DG8’s internal Programs, for simplicity. A section dealing with  
incorporating external Card Programs will be provided starting on page 40.  
Tip: Before proceeding with auditioning sounds in the DG8, raise  
the REVERB slider to its middle position. Each internal Sound  
Program contains an appropriate reverb setting and using the  
mid-point for the slider is a good place to start. You can  
always raise or lower a slider at any time to get the reverb  
level you like, or pull the slider all the way down to turn it  
completely off.  
Also, we’d like to suggest that you keep the CHORUS slider at  
its off position – all the way down – for now. Most of the  
internal Sound Programs also contain an amount of chorus,  
but when listening to the DG8’s sounds for the first time,  
Chorus should be off. This will give you the most practical  
demo of the DG8’s sounds. You can always raise the slider at  
any time to get the chorus level you like.  
Single Mode  
The DG8 is in Single mode when a Keyboard or Card Program is played alone – the  
DG8 is not in a Layer or Split. The Program’s name and label appear in the top line of  
the display under the PRIMARY SOUND heading. The Keyboard or Card Program that  
is displayed here will be appropriately called the Primary Sound or simply “the  
Primary” throughout the manual.  
The important concept to understand here is that a Primary Sound is  
always active, even when the DG8 is playing a Layer or a Split.  
In addition, the Primary Sound is always a Keyboard or a Card  
Program, and internal Keyboard Programs can never be the Split  
sound.  
DG8 REFERENCE MANUAL  
 
35  
Chapter 2: Playing the DG8  
Press any one of the Keyboard Bank buttons to select a Keyboard Bank. The last  
Keyboard Program that was selected from this Bank will be recalled from memory  
and displayed under the PRIMARY SOUND heading.  
Press the arrow to scroll through the other three Keyboard Programs in the Bank.  
Use the arrow to scroll backward through the Programs.  
You can think of a Layer as “adding another Keyboard Program to be played  
simultaneously with the current Primary”. The Keyboard Program that creates the  
Layer appears in the LAYER segment of the display.  
Likewise, a Split is created when “a Bass or Card Program is played with a Primary”.  
The Bass Program appears in the display as the SPLIT sound and is played from the  
lower range of keys. (The Layer and Split play modes are described in the following  
two topics.)  
For Primaries, Layers and Splits, the DG8’s memory independently keeps track of  
the most recently selected programs for each Bank button. This principle is true  
for the Keyboard, Bass and Card Banks.  
Layer Mode  
Layer mode takes two Keyboard Programs and puts “one on top of the other” so that  
notes played on the keyboard – or received MIDI notes – play both sounds at once.  
Both sounds are layered across the entire keyboard. A Layer can be comprised of two  
Keyboard Programs from different Keyboard Banks, the same Bank, or even the  
same Keyboard Program layered with itself.  
Tip: Before proceeding, raise the LAYER slider all the way to the top.  
At this position, the output level of the Layer sound is  
approximately equal to the Primary Sound. You can then lower  
the level of the Layer sound relative to the Primary Sound if  
necessary.  
Bear in mind that if the LAYER slider is all the way off (at the bottom),  
the Layer sound will not be heard when a Layer is created.  
36  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
There are two methods you can use to create a Layer:  
• Press and hold the LAYER/OFF button then press a Keyboard Bank button. A  
Keyboard Program from this Bank will appear in the LAYER display, layered  
with the current Program in the PRIMARY display. Use the and arrows, if  
necessary, to select the desired Keyboard Program from the Bank.  
OR  
• Press a Keyboard Bank button to select the Primary Sound. While you are still  
pressing the Keyboard Bank button, press another Keyboard Bank to select  
the Layer sound.  
• You can layer two Programs from the same Keyboard Bank. After selecting the  
desired Primary program, press and hold the LAYER/OFF button and press the  
same Keyboard Bank button. Use the and arrows to select the desired  
Keyboard Program in that Bank. Please note that this method is the only way  
you can layer two Keyboard Programs from the same Bank.  
• Once a Layer has been set up, you can change the Primary or the Layer sounds:  
- To change the Primary sound to another Program in the same Bank, press  
the PLAY button to move the cursor to the PRIMARY SOUND display. Then use  
the the or arrows to select another Program in the Bank.  
- If you want to change the Primary sound to another Bank, simply press  
another Keyboard Bank button (in this case it doesn’t matter where the  
cursor is; pressing a Keyboard Bank button automatically changes the  
Primary).  
- To change the Layer sound to another Program in the same Bank, press the  
PLAY button to move the cursor to the LAYER display, then use the the or ▼  
arrows to select another Program in the Bank.  
- If you want to change the Layer sound to another Bank, press and hold  
LAYER/OFF. While LAYER/OFF is still being pressed, press another Keyboard  
Bank button, then use the the or arrows (if necessary) to select another  
Program in the Bank.  
To exit this mode, press the LAYER/OFF button. The DG8 will remove the Layer sound  
and keep the Primary Sound. The cursor will move to the Primary Sound display.  
DG8 REFERENCE MANUAL  
 
37  
Chapter 2: Playing the DG8  
Split Mode  
A Split is simply a Bass Program played with a Primary Sound: the Bass Program  
will be played from the lower range of keys and the Primary Sound will play from  
the upper range.  
As with Primary Sounds, each Bass Bank button represents a group of four related  
Bass Programs that are selected with the and arrows:  
Tip: Before proceeding, raise the SPLIT slider all the way to the top.  
At this position, the output level of the Bass Program – the SPLIT  
sound – is approximately equal to the Primary Sound. You can  
then use the slider to lower the level of the Split sound relative to  
the Primary Sound (which remains constant) if necessary.  
Bear in mind that if the SPLIT slider is all the way off (at the  
bottom), the Bass Program will not be heard when a Split is  
selected.  
To create a Split, just press any of the Bass Bank buttons. The last Bass Program  
that was used in that Bank will be recalled and its label will appear in the SPLIT  
segment of the display. Use the and arrows, if necessary, to select the  
desired Bass Program in the Bank. The current Primary Sound will be used as  
the sound in the upper range of keys.  
After you set up a Split, you can change the sounds in the Split:  
- To change the Split sound to another Program in the same Bank, press the  
PLAY button to move the cursor to the SPLIT display, then use the the or ▼  
arrows to select another Bass Program in the Bank.  
- If you want to change the Split sound to another Bank, just press another  
Bass Bank button. Use the the or arrows (if necessary) to select another  
Program in the Bank.  
- To change the Primary sound to another Program in the same Bank, press  
the PLAY button to move the cursor to the PRIMARY SOUND display. Then use  
the the or arrows to select another Program in the Bank.  
- If you want to change the Primary sound to another Bank, simply press  
another Keyboard Bank button (in this case it doesn’t matter where the  
cursor is; pressing a Keyboard Bank button automatically changes the  
Primary).  
38  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
The default split-point is key “C2”, the C that is one octave below Middle C:  
To change the split point press the SET SPLIT button, then press any key on the  
DG8’s keyboard. This key will be the highest note of the bass range. This will  
also be the Split Point for all Splits until it is changed. And remember: you  
have two seconds to set your new split point when you press the SET SPLIT  
button. After two seconds, the display reverts back to the program display,  
leaving the current split point unchanged.  
Tip: You can also use the or arrows to set the split point. To reset the split point  
back to C2, press the and arrows together while this display is being shown.  
To exit Split mode, press the SPLIT/OFF button. The DG8 will keep the Primary  
Sound used in the Split, and the cursor will move to the Primary Sound name.  
Split-with-Layer  
When a Split is being played, you can set up a Layer to be played from the upper key  
range instead of just a single Primary sound.  
Set up a Split following the procedure for Splits on the previous page.  
Press and hold the LAYER/OFF button and press any of the Keyboard Bank  
buttons. Use the and arrows to select the desired Keyboard Program in the  
Bank to be the Layer for the upper key range (this procedure is the same as  
selecting a Layer for the whole keyboard).  
To exit the Split (and keep the Layer), press SPLIT/OFF.  
To exit the Layer (and keep the Split), press LAYER/OFF.  
To exit both Layer and Split modes to return the DG8 to Single mode, press  
LAYER/OFF and SPLIT/OFF.  
Tip: Note that you don’t have to create a Split first to play a Layer. If the DG8 is  
already playing a Layer, just press a Bass Bank and you’re there. (We could  
have easily called this “Layer-with-Split”.)  
DG8 REFERENCE MANUAL  
 
39  
Chapter 2: Playing the DG8  
USING THE EXTERNAL CARD SOUNDS  
You can take advantage of the DG8’s expandability by acquiring an Alesis QCard™  
or other compatible PCMCIA Type I sound card. The Alesis QCard is a credit-card-  
sized memory module that is pre-programmed with 128 additional sounds for  
Alesis-compatible instruments. This PCMCIA Type I card is inserted into the DG8’s  
EXPANSION CARD slot on the rear panel.  
Each QCard contains a library of new sounds that complement and expand upon the  
internal sounds in the DG8’s memory, complete with reverb, chorus and other  
effects. But please note that when used with the DG8, some effects may act  
unpredictably.  
Card Programs in Single Mode  
You can access sounds on the QCard just like the DG8’s internal Keyboard Programs:  
1. Make sure that the DG8 is in Single mode by pressing the SPLIT/OFF button  
and/or the LAYER/OFF button, if necessary.  
2. Press the CARD button just to the left of the display. The first sound in the  
Card Bank loads into the DG8 and its name and label appear in the top line of  
the display. Use the or arrows to advance or reverse through the 128  
QCard Programs numbered 000through 127.  
3. Pressing any of the Keyboard Bank buttons exits the Card Bank.  
Tip: If you press and hold either arrow button, the display will accelerate its  
scrolling through the available programs. Also, pressing both arrows together  
resets the Card Program to 000.  
Card Programs in a Layer  
You can layer a QCard Program with a DG8 Primary Sound. There are three ways of  
using this feature: the QCard as the Layer sound, the QCard as the Primary Sound or  
the QCard as both Primary and Layer.  
QCard as Layer sound:  
1. Make sure that the DG8 is not in a Split or Layer.  
2. Select an internal Keyboard Program in the DG8 by pressing any of the  
Keyboard Bank buttons. Use the and arrows, if necessary, to select the  
desired Program in the Bank.  
3. To add a QCard Program as the Layer sound, press and hold the LAYER/OFF  
button. While you are pressing LAYER/OFF, press CARD. The last Program used  
from the card as a Layer sound is recalled so you can use the and arrows,  
if necessary, to select the desired QCard Program.  
4. You can also select a Card Program for the Layer sound as you are selecting a  
Keyboard Bank: press and hold a Keyboard Bank button (to select the  
Keyboard Bank for the Primary) and while you are still holding the Keyboard  
Bank button down, press CARD. (This speeds things up by bypassing the  
LAYER/OFF button.)  
5. To exit this mode, press the LAYER/OFF button. The DG8 will turn off the Layer  
and keep the Primary Sound you selected in Step 2.  
40  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
QCard as Primary:  
1. Select a QCard Program to be the Primary by pressing the CARD button. Use  
the and arrows, if necessary, to select the desired QCard Program.  
2. Press and hold the LAYER/OFF button, then press a Keyboard Bank button. Use  
the and arrows, if necessary, to select the desired Layer sound.  
QCard as Both Primary and Layer:  
1. Select a QCard Program to be the Primary by pressing the CARD button. Use  
the and arrows, if necessary, to select the desired QCard Program.  
2. Press and hold the LAYER/OFF button, then press the CARD button again. This  
selects another QCard Program to be the Layer sound. Use the and ▼  
arrows, if necessary, to select the desired QCard Program. Please note that  
this method – using the LAYER/OFF button to create the Layer – is the only way  
you can layer two Card Programs.  
QCard Programs in a Split  
You can select a QCard Program to be the Split sound in the lower range:  
1. Press and hold the SPLIT/OFF button. While you are pressing SPLIT/OFF, press  
CARD. The QCard becomes the Split sound on the lower range of the  
keyboard. Use the and arrows, if necessary, to select the desired QCard  
Program.  
2. The DG8 will keep the current Primary Sound selected as the sound for the  
upper range of the keyboard. If necessary, press any of the Keyboard Bank  
buttons to select a new Primary Sound; use the and arrows, if necessary,  
to select the desired Keyboard Program.  
You can select a QCard program to be the Primary Sound in the upper range of a  
Split setup:  
1. Press a Bass Bank button to set up a standard split.  
2. Press the CARD button. This selects the QCard as the Primary for the upper  
range. Use the and arrows, if necessary, to select the desired QCard  
Program.  
You can select two QCard Programs in a Split setup, one for the Split sound in the  
lower range of the keyboard and one for the Primary Sound in the upper:  
1. Press and hold the SPLIT/OFF button. While you are pressing SPLIT/OFF, press  
CARD. The QCard Program becomes the Split sound on the lower range of the  
keyboard. Use the and arrows, if necessary, to select the desired QCard  
Program for the lower range.  
2. Press the CARD button (without holding any other buttons). The QCard  
becomes the Primary sound on the upper range of the keyboard. Use the ▲  
and arrows, if necessary, to select the desired QCard Program for the upper  
range.  
DG8 REFERENCE MANUAL  
 
41  
Chapter 2: Playing the DG8  
QCard Programs In a Split-with-Layer  
In the following examples, a Split is created first, then the Layer sound is added to  
complete the Split-with-Layer. Note that you don’t have to create the Split first; you  
can create a Layer first if you like, then add the Split sound. We’ll use the “Split first,  
then add the Layer” approach as just one way of accomplishing these setups:  
You can select a QCard Program to be the Layer sound of a Split-with-Layer:  
Create the Split  
1. Start off with the DG8 in Single mode, with an internal Keyboard Program as  
the Primary.  
2. Press a Bass Bank button to set up the Split; use the and arrows, if  
necessary, to select the desired Bass Program.  
Add the Layer  
3. Press and hold the LAYER/OFF button and press CARD; use the and arrows,  
if necessary, to select the desired Card Program for the Layer sound.  
Note that you can select a Card Program in Step 1 as the Primary Sound, and a  
Keyboard Program as the Layer in Step 3 if you like.  
You can select a QCard Program to be both sounds in the Layer range of a Split-with-  
Layer:  
Create the Split  
1. Start off with the DG8 in Single mode, but this time with an external Card  
Program as the Primary: press CARD and use the arrows to select the Card  
Program.  
2. Press a Bass Bank button to set up the Split; use the and arrows, if  
necessary, to select the desired Bass Program for the lower range.  
Add the Layer  
3. Press and hold the LAYER/OFF button and press CARD again; use the and ▼  
arrows, if necessary, to select the desired Card Program.  
Last, but not least, you can use the QCard for all three sounds in a Split-with-Layer:  
Create the Split  
1. Start off with the DG8 in Single mode with an external Card Program as the  
Primary: press CARD and use the arrows to select the Card Program.  
2. Press and hold SPLIT/OFF then press CARD again; use the arrows to select the  
Card Program that will be used for the SPLIT sound.  
Add the Layer  
3. Press and hold the LAYER/OFF button and press CARD for the third time; use  
the and arrows, if necessary, to select the desired Card Program.  
Do not physically remove the card from the rear slot while any Card  
Program is active. This holds true for Primary, Layer or Split.  
If a Card Program is the Primary Sound, simply switch the Card  
Program to an internal Keyboard Program. If a Card Program is the  
Layer or Split Sound, simply turn off the Layer or Split.  
42  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
DG8 SOUND CHART  
GROUP NAME  
PRIMARY SOUND LABELS  
LAYER/SPLIT SOUND LABELS  
PIANO 1  
Pno1A, Pno1B, Pno1C, Pno1D  
Pno2A, Pno2B, Pno2C, Pno2D  
Pno3A, Pno3B, Pno3C, Pno3D  
EP1 A, EP1 B, EP1 C, EP1 D  
EP2 A, EP2 B, EP2 C, EP2 D  
FMPnA, FMPnB, FMPnC, FMPnD  
HClvA, HClvB, HClvC, HClvD  
VibeA, VibeB, VibeC, VibeD  
StrgA, StrgB, StrgC, StrgD  
Piano1A, Piano1B, Piano1C, Piano1D  
Piano2A, Piano2B, Piano2C, Piano2D  
Piano3A, Piano3B, Piano3C, Piano3D  
ElPno1A, ElPno1B, ElPno1C, ElPno1D  
ElPno2A, ElPno2B, ElPno2C, ElPno2D  
FMPno A, FMPno B, FMPno C, FMPno D  
HrpClvA, HrpClvB, HrpClvC, HrpClvD  
Vibes A, Vibes B, Vibes C, Vibes D  
StringA, StringB, StringC, StringD  
PIANO 2  
PIANO 3  
ELECTRIC PIANO 1  
ELECTRIC PIANO 2  
FM PIANO  
HARPSI/CLAV  
VIBES  
STRINGS  
CHOIR  
ChorA, ChorB, ChorC, ChorD  
Pad A, Pad B, Pad C, Pad D  
SyntA, SyntB, SyntC, SyntD  
EOrgA, EOrgB, EOrgC, EOrgD  
POrgA, POrgB, POrgC, POrgD  
MultA, MultB, MultC, MultD  
Choir A, Choir B, Choir C, Choir D  
Pad A, Pad B, Pad C, Pad D  
PAD  
SYNTH  
Synth A, Synth B, Synth C, Synth D  
EOrganA, EOrganB, EOrganC, EOrganD  
POrganA, POrganB, POrganC, POrganD  
Multi A, Multi B, Multi C, Multi D  
ELECTRIC ORGAN  
PIPE ORGAN  
MULTI  
ACOUSTIC BASS  
ELECTRIC BASS 1  
ELECTRIC BASS 2  
SYNTH BASS 1  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
AcBassA, AcBassB, AcBassC, AcBassD  
EBass1A, EBass1B, EBass1C, EBass1D  
EBass2A, EBass2B, EBass2C, EBass2D  
SBass1A, SBass1B, SBass1C, SBass1D  
SBass2A, SBass2B, SBass2C, SBass2D  
PnoBasA, PnoBasB, PnoBasC, PnoBasD  
KeyBasA, KeyBasB, KeyBasC, KeyBasD  
SYNTH BASS 2  
PIANO BASS  
KEYBOARD BASS  
CARD SOUND  
Cd000 through Cd127  
Card000 through Card127  
DG8 REFERENCE MANUAL  
 
43  
Chapter 2: Playing the DG8  
FRONT PANEL CONTROLS  
TUNE  
Page 1: Master Tune  
The DG8 can be globally tuned to another instrument or tuning device, and this  
operation can be performed in any Play Mode. Press the TUNE button and use the ▲  
button to raise the pitch of the DG8 and the button to lower it. The range is ± 1 half  
step: each press of an arrow key changes the tuning by 1 cent (100 cents = 1 half step).  
Tip: Remember that if you want to do a quick reset, press the and arrows  
together. The display will reset the tuning to 00.  
Also, holding either arrow down will accelerate the scrolling of the tuning  
values.  
To exit this mode, press the PLAY button.  
Page 2: Stretch Tuning  
Pressing the TUNE button a second time enters Stretch Tuning mode which employs  
the tuning method that is actually used to tune real acoustic pianos. With Stretch  
Tuning, the low strings are tuned increasingly flat, and the high strings are tuned  
increasingly sharp compared to the equally-tempered scale.  
This function defaults to ON, and is only active on the three piano groups PIANO 1,  
PIANO 2 and PIANO 3. This feature of the DG8 was not just designed as an esoteric  
function, but provides an unusual level of realism to the piano Programs.  
While this mode is desirable when playing a piano program alone, it can cause  
problems when used with Layers or other MIDI instruments. To partially avert this,  
the DG8 automatically turns off this function when you enter Layer mode so as to  
avoid tuning conflicts with other internal DG8 Programs. However, when playing  
the DG8 with other instruments via MIDI, you may need to defeat Stretch Tuning  
because the high and low ends of the DG8 may sound out of tune with other MIDI  
instruments. Use the arrow to turn this function OFF. When Stretch Tuning is off,  
the piano programs will always be tuned to the equally-tempered scale whether used  
as a Primary sound or as a Layer sound.  
Note that, like other settings in the DG8, if turning Stretch Tuning is set to OFFit will  
remain off until you change it or re-initialize the instrument.  
To exit this mode, press the PLAY button.  
TRANSPOSE  
You can transpose the DG8 ± 1 octave. Using Middle C (key “C3”) as your reference,  
press and hold the TRANSPOSE button and press a key on the keyboard. Pressing a  
key above Middle C will transpose the DG8 up by the interval and pressing a key  
below Middle C will transpose the DG8 down by that interval.  
Tip: You can also use the or arrows to transpose. To reset the transpose to  
Middle C, press the and arrows together while this display is being shown.  
The selected key will be the new key for the DG8 in any Play mode until it is  
changed. The Transpose function actually changes the MIDI Note Number sent by  
44  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
the keyboard globally (affects all modes), whether to an external MIDI device or to the  
internal DG8 sounds or card sounds. Once the keyboard is transposed, all Primaries,  
Layers and Splits are transposed by the same interval until you change the transpose  
(even if the DG8 is turned off) or re-initialize the instrument.  
Also, if you attempt a transpose value more than the one-octave limit, the DG8 will  
keep the pitch the same but the key selected will be the nearest one within the one  
octave range. For example, if you try to transpose up to key E5 (the highest E on the  
keyboard), the DG8 will transpose the keyboard up to E3, the E above Middle C.  
Also, transposing the keyboard will not effect the Split Point’s physical location on  
the keyboard.  
The Transpose display will exit as soon as you press a key on the DG8’s keyboard. To  
exit this mode without transposing, press PLAY.  
EFFECTS  
Reverb and Chorus have been pre-programmed into nearly all* of the DG8’s sounds.  
You adjust the level of the effects by moving the appropriate LEVEL slider. Just keep  
in mind that the Reverb and Chorus amounts are determined by the sliders’  
positions, so if a slider is all the way down, that effect will not be heard at all.  
* The exception to this is the ELECTRIC ORGAN Bank which substitutes a rotating speaker effect  
instead of chorus. The CHORUS LEVEL slider acts as a speed control for the rotating speaker.  
Note that Bass Programs have a minimal amount of Reverb and Chorus.  
GRAPHIC EQ  
The DG8’s stereo 5-band graphic equalizer provides the tone controls for shaping the  
overall sound output of the instrument. Press the EQ ON button to activate the  
equalizer. Each slider provides 6dB of boost or cut around each frequency.  
The settings made on the EQ affect all sounds in all Play Modes – Primary, Layer,  
Spilt and Split-with-Layer – and affect all inputs and outputs including the DG8’s  
built-in speakers and headphones. The EQ is also “post-effects” so that reverb,  
chorus and rotary speaker effects are equalized as well. The EQ settings are not  
changed at power-up or if the DG8 is initialized, but every time you power on the  
DG8, the EQ will be off.  
DG8 REFERENCE MANUAL  
 
45  
Chapter 2: Playing the DG8  
MIDI FUNCTIONS  
Pressing the MIDI button puts the DG8 into MIDI Edit mode.  
Pressing the MIDI button repeatedly will step through the six different pages of the  
DG8’s MIDI functions.  
Press the PLAY button to exit any of the pages in this mode.  
Page 1: Basic MIDI Channel  
This is the MIDI Channel for Primary Sounds and Layers. The MIDI Channel  
assignments for Layer Program Changes and Split channels follow sequentially:  
Layer Program Changes = Basic Channel + 1, Splits = Basic Channel + 2.  
The DG8 operates in MIDI “Mode 3: Omni Off/Poly” only, and defaults to MIDI  
Channel 1. To set the DG8 to transmit and receive on another MIDI Channel:  
1. Press the MIDI button. The last MIDI function display that was accessed will be  
shown. Press the MIDI button repeatedly until the display reads:  
BASIC  
MIDI Channel = X  
... where Xis one of the 16 MIDI Channels or Off. When set to Off, the DG8  
will neither transmit nor receive MIDI information.  
2. Use the and arrows to select the new Basic MIDI Channel or Off.  
3. To confirm your selection and exit this mode, press PLAY.  
The DG8 transmits and receives the following MIDI data. Exceptions are noted in  
parentheses:  
Channel Messages  
Pitch Bend (receive only)  
Velocity  
Release Velocity (receive only)  
Program Changes  
Controller Name  
Bank Select (for QCard access)  
Modulation  
MIDI Controller #  
0
1
7
Volume  
Pan (receive only)  
Expression (receive only)  
10  
11  
Sustain Pedal  
Sostenuto Pedal  
Soft Pedal  
64  
66  
67  
Reverb Level  
Chorus Level  
91  
93  
46  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
Page 2: Local Control  
It is possible to use the DG8 as a MIDI controller in a MIDI system without playing  
its own internal or card sounds by turning Local Control off. In this situation, the  
DG8’s keyboard becomes a MIDI transmitter only and does not affect the voices.  
This feature is particularly useful when playing the DG8 with a sequencer. The  
sequencer controls the DG8 while the DG8’s keyboard can be used to play another  
MIDI instrument. Just be sure that the sequencer (or any device controlling the DG8)  
is not “echoing” MIDI notes from the DG8’s keyboard back into the DG8 (unless  
that’s what you want to do).  
When this display is shown, pressing the and arrows turns Local Control ON(the  
default setting: the keyboard plays the DG8 normally) or OFF(the DG8’s keyboard  
plays to MIDI OUT only).  
Page 3: AUX Pedal Assignment  
This page allows you to determine how the rear panel FOOT PEDAL AUX jack responds  
to a pedal input, either modulation – rotating speaker for the ELECTRIC ORGAN Bank –  
or volume control. This means that you can tell the DG8 that if a pedal is plugged  
into the AUX jack, it be either a modulation pedal or a volume control pedal.  
When this display is shown, pressing the and arrows toggles between  
Modulationand Volume. The default setting is Volume.  
Page 4: Keyboard Scaling  
This function is a sensitivity control for the DG8’s velocity response. This function  
tells the DG8 how to respond to changes in how hard or how soft you play the keys.  
When this page is displayed, you will have a choice of values between 00and 99  
with the default setting at 50. It’s harder to play loudly and easy to play softly when  
Keyboard Scaling is set to 00.  
At the other extreme, a setting of 99makes it very easy to play loudly and difficult to  
play softly.  
Use the and arrows to scroll through the range until the desired scaling value is  
displayed. Pressing and together resets the display to the default value of 50.  
Page 5: Bass Sustain  
When using the sustain pedal in Split mode, it is usually not desirable to have the  
left-hand bass sustain when the pedal is stepped on. This parameter defaults to OFF  
so that only the sound on the upper key range sustains. Use the and arrows to  
turn this function ONif you want the Bass Programs to sustain with the pedal.  
Page 6: Sustain Catching  
There may be circumstances where the DG8’s Sustain Pedal Catching function is not  
especially useful for what you’re playing. Use the and arrows on this page to  
turn the Sustain Catching feature of the DG8 ONor OFF. For details on what this  
function does, see the description on the next page. Its default setting is ON.  
DG8 REFERENCE MANUAL  
 
47  
Chapter 2: Playing the DG8  
PEDALS  
BACKGROUND  
Understanding the keyboard mechanism of an acoustic piano will help in under-  
standing how the pedals operate on the DG8. Before a piano is played, a series of  
dampers – small blocks of a felt-like material – rest on each string to prevent them  
from vibrating. When a key is played, the damper for that note lifts up and a hammer  
strikes the string (and immediately falls back allowing the string to vibrate). As long  
as you are holding down that key, the damper stays lifted allowing the string to  
vibrate freely. When the key is released, the damper falls back on the string and stops  
it from vibrating.  
The pedals of an acoustic piano are used to modify the action of the dampers. The  
DG8’s pedals emulate the action of an acoustic piano’s pedals electronically. The  
following descriptions illustrate how each pedal works on the DG8.  
SUSTAIN  
The DG8’s Sustain pedal provides the digital equivalent of the traditional sustain  
capability of an acoustic piano: all dampers are lifted allowing all played keys to  
sustain as long as the pedal is held down. This provides the rich sound we associate  
with an acoustic piano. Releasing the pedal causes all vibrating strings to mute due  
to the action of the dampers. If the pedal is kept down long enough, the sustained  
notes will fade to silence.  
On the DG8, keys played while the Sustain pedal is down will sustain and fade until  
the pedal is released. There are, however, many variations on the way you can use  
the Sustain pedal. An great amount of flexibility in musical expression can be  
achieved in the way the Sustain pedal is used while playing. Here are a few things  
we built into the DG8:  
a) Sustain Pedal “Catching”: If a key or keys are played quickly and the sustain  
pedal is pressed after the keys are released, the sustain of the notes can be  
“caught” before it fades out completely. The notes will then sustain and fade  
from the point where the Sustain Pedal is pressed.  
b) Re-Entering Sustain: If the pedal is sustaining a note or notes and the pedal is  
released and then suddenly stepped on again, the DG8 will resume the  
sustained note(s) but at a lower volume. This imitates the tendency of the  
mechanical damping action of an acoustic piano to take some amount of time  
to stop played strings from vibrating. If a damper isn’t given enough time to  
fully stop the strings, they will continue to vibrate, although with less energy.  
This can be repeated several times until the sound has completely faded out.  
Although these two features correctly emulate the behavior of a real piano, they can  
rob the DG8 of voices and/or make sequences which were recorded on a MIDI  
device without a sustain catching feature sound a bit muddy. Conversely, if a pre-  
recorded sequence sounds a bit “choppy”, try turning Sustain Catching to ON. The  
Sustain Pedal Catching and Re-entering Sustain features can both be defeated by  
setting Sustain Catching to OFF.  
48  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
SOSTENUTO  
This pedal on an acoustic grand piano* causes only the dampers on played keys to  
lift until the pedal is released. In other words, if you play a chord, step on the  
Sostenuto pedal, and then release the keys, the notes you were playing continue to  
ring. What makes this different from a sustain pedal is that you can play every other  
note on the keyboard and they won’t sustain, but if you play the notes you were  
holding when you stepped on the sostenuto pedal, they will still sustain. Try a  
glissando down the keys and you’ll hear the chord you played spelled out as you  
pass those notes!  
On the DG8, this pedal produces the digital equivalent of “lifting dampers” only on  
the played keys.  
* NOTE: The DG8 emulates the sostenuto pedal of a grand piano, not an upright, and we want  
to make that distinction clear. On upright pianos, what the “middle pedal” does varies from  
brand to brand.  
SOFT PEDAL  
This pedal on an acoustic piano is so named because it produces a quieter  
performance. The way acoustic pianos accomplish this varies. In some pianos, the  
soft pedal causes all dampers to be lifted but not as high as the sustain pedal lifts  
them, so that the brightness and loudness of the notes are “softened”. In others, the  
soft pedal accomplishes its task by shifting the position of the keybed so the  
hammers strike the strings in a different way.  
This last option takes two different forms. For example, all acoustic pianos have  
many notes for which there are two or more strings per key. On a concert grand  
piano, the soft pedal physically moves the keybed sideways so the hammers strike  
fewer strings per key.  
Other pianos employ a third method that lowers the entire set of keys into the  
keybed a little. This reduces the distance the keys are able to travel, which in turn  
limits the amount of kinetic energy which can be transferred from the hammers into  
the strings, thereby resulting in a quieter performance.  
On the DG8, this pedal achieves a similar “softening” of the brightness and loudness  
by reducing the keyboard’s response to velocity, which therefore makes the sound  
somewhat lower in volume and brightness.  
PEDAL CONNECTIONS  
Momentary footswitches are used for the Sustain, Sostenuto and Soft Pedal features of  
the DG8. “Momentary” means that it is a spring-loaded switch that operates by  
“pressing and releasing”.  
Pedals are plugged into the DG8’s rear panel jacks. Each jack is labeled so that you’ll  
know which pedal performs which function.  
These pedals – they’re actually electrical switches, but we’ll refer to them as pedals to  
keep consistent with piano terms – are designed to reproduce the same response as  
their acoustic counterparts. But since we’re dealing with an electronic instrument, the  
concept here is that when a switch like this is pressed, it is in its on position; when  
you release it, it’s off.  
DG8 REFERENCE MANUAL  
 
49  
Chapter 2: Playing the DG8  
A momentary foot switch with a 2-conductor 1/4” connector is used for the Soft Pedal  
function of the DG8. A momentary footswitch with a 3-conductor 1/4” connector is  
used for the Sustain/Sostenuto functions of the DG8. “Momentary” means that it is a  
spring-loaded switch that operates by “pressing and releasing” for on (press) or off  
(release) signals.  
If you use a footswitch with a 2-conductor connector for Sustain/  
Sostenuto, the Sostenuto function will NOT operate.  
Potentiometer foot pedals with 2-conductor connectors are used for volume and  
modulation. “Potentiometer” means that the pedal mechanically operates an internal  
knob (technically known as a potentiometer) giving you “more” or “less” rather than  
“on” or “off” like a switch. These pedals are often referred to as “rocker pedals”.  
The diagram below shows what the right kind of connector looks if you want to  
purchase footpedals, or if you need a pedal that is different from the one shipped  
with the DG8.  
Plug the pedals into the DG8’s back panel jacks. Each jack is labeled so that you’ll  
know which pedal or switch performs which function.  
For the volume or modulation pedal, use the AUX jack. Note that the DG8 must be set  
to perform either volume control or modulation, not both. To select the operation of  
the pedal, press the MIDI button on the front panel repeatedly until AUXPedal  
appears the in the display. Use the or arrows to select between Modulationor  
Volume. Press the PLAY button to confirm your choice and return the DG8 back to  
Play mode.  
50  
DG8 REFERENCE MANUAL  
 
Chapter 2: Playing the DG8  
AUDIO INPUTS AND OUTPUTS  
The DG8 uses standard 2-conductor 1/4” tip-sleeve unbalanced connectors for back  
panel audio connections and a 3-conductor 1/4” tip-ring-sleeve connector for the two  
headphone outputs on the front. The diagram below shows what the right kind of  
connector looks like when purchasing audio cables and headphones.  
Outputs  
To connect your DG8 to a sound system in stereo, connect two 2-conductor  
unbalanced audio cables from the unit’s R and L/MONO jacks on the back panel  
OUTPUTS section to two inputs on your sound system. If you are connecting the DG8  
to a mixer, pan the channels hard left and right to obtain a full stereo image.  
To connect your DG8 to a sound system in mono, connect a 2-conductor unbalanced  
audio cable from the unit’s L/MONO jack on the back panel OUTPUTS section to an  
input on your sound system.  
Tip: If necessary, you can turn the DG8’s internal sound system off. There’s a slide  
switch on the back panel adjacent to the stereo outputs that turns the speakers  
on or off.  
Inputs  
The DG8 accommodates audio inputs from such sources as a stereo cassette or audio  
CD player. These signals are mixed with the DG8’s internal sound system and output  
to the speakers. The DG8’s VOLUME slider adjusts the volume level of the composite  
mix of the DG8’s internal sounds, external card sounds and signals coming into the  
INPUTS jacks. The level of the cassette or CD player must be set on the cassette or CD  
player itself in order to control it separately from the DG8’s internal sounds.  
To connect an external audio source in stereo, connect two 2-conductor unbalanced  
audio cables from the source to the DG8’s R and L/MONO jacks on the back panel  
INPUTS section. To connect an external audio source in mono, use one 2-conductor  
unbalanced cable from the source to the L/MONO jack. This will route the mono signal  
to both speakers. Plugging the cable into the R jack will route the sound to the right  
speaker only.  
DG8 REFERENCE MANUAL  
 
51  
Chapter 2: Playing the DG8  
INITIALIZING THE DG8  
FACTORY DEFAULTS  
When the DG8 is shipped from the factory, its user parameters are set to certain  
values so that the unit will perform its most basic functions right out of the box.  
These are called defaults – values that are set at the factory as the most useful and/or  
logical starting points for the various functions within the unit. You may have  
noticed this as you explored the DG8’s functions, and this manual refers to these  
default values from time to time.  
If for any reason you want to return the DG8 to the state it was in when it shipped,  
you can initialize (perform a complete reset) of the DG8 and return it to its default  
state. This feature is particularly useful in the event a power problem causes the DG8  
to behave strangely, or if certain functions do not seem to be operating as expected.  
To initialize the DG8:  
Turn it off.  
Press and hold the and arrows.  
While the arrows are being held down, turn the DG8 back on.  
This simple procedure resets the following parameters:  
MIDI volume is reset to the maximum of 127for the Primary Sound,  
Layer and Split  
EQ is turned off  
modulation is reset to 0  
Program Piano1Ais selected with no Layers or Splits  
all Primary Sound and Bass Program sound banks are reset to the Aprogram.  
Selecting a Card Program will recall program 000whether used as Primary  
Layer or Split.  
tuning is reset to A440; the MasterTunedisplay resets to 00  
default Split Point is reset to key “C2”, the C one octave below Middle C  
the AUX pedal is reset to Volume  
Keyboard Scaling is reset to the mid-point value of 50  
Stretch Tuning is turned on  
Sustain Catch is turned on  
Local Control is turned on  
Basic MIDI Channel is set to 1  
Bass Sustain is turned off  
POWER-UP RESETTING  
There are two parameters and one function which reset every time you turn the DG8  
on. Modulation and volume values are reset upon power up, and the EQ ON/OFF  
button is turned off.  
52  
DG8 REFERENCE MANUAL  
 
Chapter 3: MIDI Functions  
CHAPTER 3  
MIDI FUNCTIONS  
MIDI BASICS  
Before we delve into the specific MIDI functions of the DG8, we’d like to provide a  
brief background on MIDI for those who may not be familiar with this technology.  
MIDI (pronounced “MID-ee”) is the acronym for Musical Instrument Digital  
Interface. It was developed and adopted by electronic musical instrument  
manufacturers in the early 1980s as a common system of connecting electronic  
musical instruments and devices so that they could share music data as well as other  
digital information.  
Just about any device that has a microprocessor (synthesizers, samplers, sequencers  
and drum machines, analog and digital recorders and mixers, effects devices and  
computers) can share music data (notes and chords) and various digital information  
such as pitch bend and vibrato, sustain and volume pedal, keyboard velocity,  
pressure and aftertouch, patch change commands, timing data (called “MIDI Clock”)  
and a wide variety other types of data.  
Thus, virtually any musical expression that is generated by an electronic musical  
device could be shared in a system of MIDI devices. But we are not limited to  
musical applications alone. With the addition of MIDI Time Code for example, the  
ability to interface a music system with video production was realized. There are  
even stage lighting systems that use MIDI for programming light control and data  
storage.  
A document called the MIDI Specification describes all possible MIDI functions and  
how they should work. Manufacturers use this spec when designing products so that  
a fairly high level of compatibility among different brands can be reasonably  
expected.  
Generally, a manufacturer will also include a MIDI Implementation chart with each  
product so that you can know how MIDI was designed into that particular model.  
This is usually helpful to know because not every MIDI function needs to be  
included in every musical product. For example, certain MIDI functions that are  
unique to keyboard instruments are unnecessary on, say, digital effects devices.  
Manufacturers have the option of including whatever MIDI functions are  
appropriate to the product. You can find the MIDI Implementation chart for the DG8  
on page 67.  
DG8 REFERENCE MANUAL  
 
53  
Chapter 3: MIDI Functions  
MIDI HARDWARE  
MIDI instruments and devices are connected by a fairly simple system of cables. The  
MIDI OUT port transmits data from one device one-way through the cable to the  
receiving instrument’s MIDI IN. You can setup each device in the system to send and  
respond to MIDI commands in a certain way. For example, you can tell a keyboard  
or guitar synth to send everything in MIDI except for Program Change commands.  
By the same token, you can tell your sound module to respond to any MIDI  
command sent to it but ignore Velocity data.  
MIDI THRU simply passes data received by MIDI IN right back out to another device  
connected to it. This makes “chaining” possible in a MIDI system. For some examples  
in connecting MIDI devices together, see our illustrations in the section entitled The  
DG8 in a Music System starting on page 20.  
Also of importance in discussing MIDI hardware is the term voice. An instrument’s  
voice is the most basic unit of sound generation. It can be an integrated circuit chip  
(or chips) or can be a sampled sound in the instrument’s memory, like the DG8.  
MIDI MESSAGES  
The are two types of MIDI messages that are communicated through your network  
of MIDI cables: Channel and System.  
Channel Messages are typically the messages you’ll be most concerned with for  
routine MIDI operations and can originate (be transmitted) from virtually any device  
in the system. MIDI provides 16 “Channels” through which certain MIDI data is  
shared among devices in the system. The communication of certain messages along  
Channels makes it possible to connect many devices together but allows you to  
specify which devices communicate directly with each other. For example, you  
could have seven MIDI devices that are all connected to each other. Two of the  
devices can be communicating on Channel 2, two others on Channel 9 and the  
remaining three on Channel 4, as one possible setup.  
Channel messages are further divided into two groups: Voice messages and Mode  
messages. Because these messages are channelized – they are communicated on a  
designated Channel number – they are only recognized by instruments that have  
been set to receive on that Channel.  
System messages, on the other hand, do not have a channel number and can be  
received by any device in a system. This permits devices in a MIDI system to share  
certain data without having to be set to a particular Channel. System messages, like  
Channel messages, can originate from just about any MIDI device in the system. The  
three types of System messages are called Real Time messages, Common messages and  
Exclusive messages. Because none of these types of messages are implemented on the  
DG8, we will not be covering them in this manual.  
CHANNEL MESSAGES: VOICE MESSAGES  
Each MIDI device is assigned a Basic MIDI Channel. This is the MIDI Channel that the  
instrument will use to transmit MIDI data and can be set to any Channel # 1 - 16.  
This is also the MIDI Channel that the instrument will receive on.  
This principle is not set in concrete, however. For many MIDI instruments, the ability  
to communicate – both transmit and receive – on several Channels at once is quite  
54  
DG8 REFERENCE MANUAL  
 
Chapter 3: MIDI Functions  
common. For example, certain instruments are designed such that you can set a  
Voice or group of voices to MIDI Channels other than the Basic Channel. This  
provides enormous flexibility in the way that the instrument can control other  
instruments in the system, or be controlled by another MIDI device. You might want  
to think of a device’s Basic Channel as the one on which other Channels can be based  
– hence the word “basic”. A good place to start is a setup that instructs the unit to  
transmit and receive on the Basic Channel, then build from there if you need to.  
The DG8 is a prime example of a multiple MIDI Channel instrument in that three  
successive MIDI Channels are designated to communicate data: Primary Sounds and  
Layers transmit and receive on the Basic Channel except Program Change  
commands for Layers, which happen on the next higher Channel (Basic Channel +1);  
Splits transmit and receive on the next higher Channel (Basic Channel + 2). For an in-  
depth look at how this is implemented on the DG8, see page 58.  
MIDI messages that affect your instrument’s voices include:  
Note On. This message communicates that a particular note is being played and  
corresponds to a key being pressed down; values range from 000 (the lowest possible  
note) to 127 (the highest possible note). Middle C is MIDI Note #60.  
Note Off. Where a Note On message communicates when a note is to be played, this  
message tells when the key has been released. This may appear a little like overkill,  
but remember that we’re dealing with computers here: every action requires a  
corresponding message to be communicated.  
Velocity. A Velocity message corresponds to the dynamics of your playing by telling  
the receiving device how quickly (or slowly) a note was played. Typically, Velocity  
affects the loudness and brightness of the sound – playing harder makes the sound  
louder and brighter; playing softly makes the sound quieter and less bright. In the  
more elaborate products, this data can be routed to other aspects of the sound as well  
for some very interesting results. Velocity values range from 001 (minimum velocity)  
to 127 (maximum velocity). A velocity of 000 is equivalent to a Note Off message.  
Program Change. Sending a Program Change command from a sequencer or another  
MIDI keyboard can change synth patches automatically. There are 128 Program  
Change command numbers.  
Also note that not all instruments and devices number programs consistently. Some  
number them as 000-127, others as 001-128, and still others arrange programs in  
banks of eight programs (such as A1-A8, B1-B8, C1-C8, etc.) or, as in the case of the  
DG8, Banks of four programs designated A, B, C and D.  
Pitch Bend. This “bends” a note from its standard pitch.  
Continuous Controllers. This term is sometimes abbreviated “CC” and is followed  
by a number sign and a number, as in “CC #7”. If you look at the chart on the next  
page, you’ll see that “Continuous Controller # 7” controls MIDI (or Main) Volume.  
What we mean by “continuous” is that the controller is able “to go from 0 to 127 in  
increments of 1”. Although this might first appear as a rough stepping from one  
value to the next, the resolution of 128 increments is small enough to provide a  
smooth transition through this range. If this resolution is not fine enough, the  
manufacturer can opt to add more resolution by using a second byte to define the  
range. Controller #’s 32 through 63 are used for this purpose.  
Footpedals, breath controllers, and modulation wheels can vary sounds as you play,  
thus adding expressiveness. MIDI allows for 32 continuous controllers and 58  
DG8 REFERENCE MANUAL  
 
55  
Chapter 3: MIDI Functions  
continuous/switch controllers (which can act like continuous controllers, but some  
are assumed to choose between two possible states, such as on and off).  
Each type of controller is stamped with its own controller identification number. Not  
all controller numbers have been standardized for specific functions, but the  
following indicates the current list of assigned controllers.  
CONTROLLER #  
FUNCTION  
DATA RANGE  
0
Bank Select  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
0 - 127  
1
Modulation Wheel  
Breath Controller  
Early DX7 Aftertouch  
Foot Controller  
Portamento Time  
Data Slider  
2
3
4
5
6
7
Main Volume  
8
Balance  
10  
11  
16  
17  
18  
19  
Pan  
Expression  
General Purpose #1  
General Purpose #2  
General Purpose #3  
General Purpose #4  
32-63  
Least Significant Bytes (LSB), Controllers 0-31  
0 - 127  
64  
65  
66  
67  
69  
80  
81  
82  
83  
Sustain Pedal  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
0 or 127  
Portamento On/Off  
Sostenuto Pedal  
Soft Pedal  
Hold 2  
General Purpose #5  
General Purpose #6  
General Purpose #7  
General Purpose #8  
91  
Reverb Depth  
0 - 127  
92  
Tremolo Depth  
0 - 127  
93  
Chorus Depth  
0 - 127  
94  
Celeste Depth  
0 - 127  
95  
Phase Depth  
0 - 127  
96  
Data Increment  
0 or 127  
97  
Data Decrement  
Non-Registered Parameter MSB  
Non-Registered Parameter LSB  
Registered Parameter MSB  
Registered Parameter LSB  
Reset All Controllers  
Local Control On/Off  
All Notes Off  
0 or 127  
98  
0 - 127  
99  
0 - 127  
100  
101  
121  
122  
123  
124  
125  
126  
127  
0 - 127  
0 - 127  
0
0 or 127  
0
Omni Off  
0
Omni On  
0
Mono On  
0-16; 0 = Omni Off  
0
Poly On  
56  
DG8 REFERENCE MANUAL  
 
Chapter 3: MIDI Functions  
CHANNEL MESSAGES: MODE MESSAGES  
There are four types of messages that determine the MIDI Mode of the instrument.  
The “mode” of a device refers to how it will respond to incoming MIDI data. The  
MIDI Specification outlines four possible modes and the DG8 implements a modified  
version of one of these four modes called “Mode 3: Omni Off/Poly”.  
Mode 3 describes how polyphonic instruments in general receive notes on one  
Channel only. But as we discovered on page 55, the DG8 uses multiple MIDI  
Channels when communicating with other devices. Three successive MIDI Channels  
are designated to communicate data: Primary Sounds and Layers transmit and  
receive on the Basic Channel except Program Change commands for Layers, which  
happen on the next higher Channel (Basic Channel +1); Splits transmit and receive on  
the next higher Channel (Basic Channel + 2). For an in-depth look at how this is  
implemented on the DG8, see page 58.  
Portions of this Chapter are abridged versions of material from Power Sequencing with Master Tracks Pro/Pro  
4 and The Complete Guide to the Alesis HR-16 and MMT-8, copyright 1990 and 1989 respectively by AMSCO  
Publications, and are adapted with permission.  
DG8 REFERENCE MANUAL  
 
57  
Chapter 3: MIDI Functions  
MIDI AND THE DG8  
With the previous description of MIDI basics in mind, let’s continue with a few more  
details concerning the MIDI functions that are present in the DG8. A MIDI  
Implementation Chart is provided in Appendix C that lists the MIDI functions  
supported by the DG8.  
CHANNEL MESSAGES  
As we mentioned in the “Voice Messages” section of this Chapter, certain  
instruments are designed such that you can set a voice or group of voices to MIDI  
Channels other than the Basic Channel the instrument has been set to. This is an  
important concept to understand when setting up the DG8 as a master (transmitting  
MIDI to other instruments) or as a slave (receiving MIDI from other instruments) in a  
MIDI music system.  
In the case of the DG8, a “group of voices” would be the two Programs in a Layer, as  
one example – the Primary Sound plus the Layer sound. Some of the DG8’s voices  
are allocated to the Primary Sound and some to the Layer sound. For a Split, voices  
are grouped for the Bass Program played from the lower range of the keyboard and  
the Primary Sound played from the upper range, as another example of voice  
grouping.  
A key point to consider when using MIDI on the DG8 is that three successive MIDI  
Channels are designated to transmit and/or receive data: the Primary Sound and  
Layer transmit and receive on the Basic Channel with one exception which is  
Program Change commands for the Layer which happens on the next higher  
Channel (Basic Channel + 1). A Split transmits and receives on the next higher  
Channel (Basic Channel + 2). Note that Program Change commands for the Bass  
Program only occur on the Basic Channel +2.  
Therefore, if you set the DG8’s Basic MIDI Channel to, say, Channel 6, the Primary  
Sound and Layer transmit and receive on Channel 6 (the Basic Channel), Program  
Change commands for the Layer occur on Channel 7 (Basic Channel + 1) and the  
Split transmits and receives on Channel 8 (Basic Channel + 2).  
When you first power on the DG8, it defaults to the following MIDI settings:  
MIDI Basic Channel: Channel 1  
Receive – Mode 3: OMNI Mode off/Poly.  
MIDI Channel 1  
Primary Sound  
Layer  
all supported Channel Messages  
all supported Channel Messages except Program  
Change commands  
MIDI Channel 2  
MIDI Channel 3  
Program Change commands (only) for the Layer sound  
Split  
all supported Channel Messages  
Program Change commands only affect the  
Bass Program.  
58  
DG8 REFERENCE MANUAL  
 
Chapter 3: MIDI Functions  
Program Changes  
The way the DG8 sends and responds to MIDI Program Change commands was  
designed to imitate the way Programs – whether Primary, Layer or Split – are  
selected from the front panel buttons. This is an important concept to understand  
and the following examples will help to illustrate how this works in the real world.  
Specific MIDI operations are explained with these examples:  
1. When the DG8 is playing Primary Sounds only (not in a Layer or Split) and  
you press a Keyboard Bank button, the DG8 recalls the last Keyboard  
Program that was used in that Bank and transmits its MIDI Program Number  
on the Basic Channel.  
If you use the or arrows to select another Keyboard Program in that Bank,  
the MIDI Program Number that corresponds to each Keyboard Program as it  
comes up in the display is also sent on the Basic Channel.  
MIDI Program Numbers 000 through 003 correspond to DG8 Keyboard  
Programs Piano 1 “A” through “D”; MIDI Program Numbers 004 through 007  
correspond to DG8 Keyboard Programs Piano 2 “A” through “D” and so on  
up to MIDI Program 059.  
Card Programs are easier to keep track of since they correspond with MIDI  
Program Numbers exactly: Card Program 000 = MIDI Program Number 000,  
Card Program 001 = MIDI Program Number 001, and so forth on up to 127.  
2. Since the Layer sound comes from the same sound banks as the Primary  
Sounds (either the Keyboard Banks or a Card), the same MIDI Program  
Change rules apply as in the examples above. Just remember that when  
changing the Layer sound from the DG8’s front panel, the MIDI Program  
Change number is transmitted from the DG8 on the Basic Channel + 1. When  
sending the DG8 a Program Change command from another device in your  
rig with the intent of changing the Layer sound, be sure to send it to the DG8  
on this Channel.  
3. When a Bass Bank button is pressed, the DG8 recalls the last Bass Program  
that was used in that Bank and transmits its MIDI Program Number on the  
Basic Channel + 2.  
If you use the or arrows to select another Bass Program in that Bank, the  
MIDI Program Number that corresponds to each Bass Program as it comes up  
in the display is also sent on the Basic Channel + 2.  
MIDI Program Numbers 000 through 003 correspond to DG8 Bass Programs  
Acoustic Bass “A” through “D”; MIDI Program Numbers 004 through 007  
correspond to DG8 Bass Programs Electric Bass 1 “A” through “D” and so on  
up to MIDI Program 027. Notice that the same range of MIDI Program  
Numbers are used for the Bass Programs as for the Keyboard and Card  
Programs. But not to worry: since Program Change messages are  
communicated on different MIDI Channels for Primaries, Layers and Splits,  
no conflicts should occur.  
DG8 REFERENCE MANUAL  
 
59  
Chapter 3: MIDI Functions  
The following chart summarizes the DG8’s handling of transmitting and  
receiving MIDI Program Change commands:  
MIDI Program #  
Primary/Layer  
Program  
Primary  
Channel  
Layer  
Channel  
Bass  
Program  
Split  
Channel  
000  
001  
002  
003  
Pno1A  
Pno1B  
Pno1C  
Pno1D  
Basic  
Basic  
Basic  
Basic  
Basic + 1  
Basic + 1  
Basic + 1  
Basic + 1  
ABasA  
ABasB  
ABasC  
ABasD  
Basic + 2  
Basic + 2  
Basic + 2  
Basic + 2  
024  
025  
026  
027  
HClvA  
HClvB  
HClvC  
HClvD  
Basic  
Basic  
Basic  
Basic  
Basic + 1  
Basic + 1  
Basic + 1  
Basic + 1  
KBasA  
KBasB  
KBasC  
KBasD  
Basic + 2  
Basic + 2  
Basic + 2  
Basic + 2  
056  
057  
058  
059  
MultA  
MultB  
MultC  
MultD  
Basic  
Basic  
Basic  
Basic  
Basic + 1  
Basic + 1  
Basic + 1  
Basic + 1  
4. When using MIDI Bank Select commands to remotely change banks on the  
DG8, internal Primary and Layer sounds are MIDI Bank 1, Bass sounds are  
MIDI Bank 2 and Card sounds are MIDI Bank 3. Card sounds are always  
MIDI Bank 3 regardless of whether they are used as a Primary, Layer or Split.  
Pedals  
The DG8 transmits and receives pedal messages in accordance with the MIDI  
Specification: Sustain Pedal is assigned Controller #64, Sostenuto Pedal is assigned  
Controller #66 and Soft Pedal is assigned Controller #67.  
Care must be taken when you are sending the DG8 MIDI Pedal messages. If you are  
playing the DG8 from a MIDI master that only has a sustain pedal, it will most likely  
be sending Controller #64. So if you intend to use the Soft Pedal function, for  
example, you will need to change your master to transmit the Soft Pedal message  
(MIDI Controller #67) instead of Sustain Pedal (MIDI Controller #64).  
60  
DG8 REFERENCE MANUAL  
 
Appendix A: Glossary  
GLOSSARY  
DG8 TERMS  
Bass Program  
Card Program  
a sound Program selected from one of the Bass Banks  
a sound Program selected from the “Card Bank”, an external  
sound card inserted into the DG8’s back panel  
Defaults  
settings or display values that are set at the factory as the most  
useful and/or logical starting points for the various functions  
within the unit  
Graphic EQ  
short for “graphic equalizer”, the five sliders on the left side of  
the DG8’s control panel that are used to adjust the tone of the  
sound output; the audio spectrum of the DG8 is divided into five  
“frequency bands” or ranges that can be boost or cut ± 6 dB.  
Initialize  
to perform a complete reset of the DG8’s functions to its defaults;  
see “Defaults”  
Keyboard Program a sound Program selected from one of the Keyboard Banks  
Layer  
a combination of two Keyboard or Card Programs in which  
playing the DG8 plays both sounds at once; this term also refers  
to the selected LAYER sound shown in the display  
Primary Sound  
Split  
the sound program shown in the display selected from the  
Keyboard Banks or the Card Bank; the Primary Sound is active  
in all Play Modes: Single, Layer, Split and Split-with-Layer  
the keyboard of the DG8 is divided into two play ranges: one of  
the 28 Bass Programs is assigned to the lower range of the  
keyboard (normally played with the left hand) and one of the 60  
Primary Sounds assigned to the upper range of the keyboard  
(normally played with the right hand); see also “Split Point”  
Split Point  
the key that determines where the two ranges of a split are  
divided; the Split Point is the highest key of the “lower” range  
Split-with-Layer  
a keyboard setup where the Split function (a Bass Program on  
the lower range of keys) is used with the Primary Sound and a  
Layer on the upper key range  
Soft Pedal  
pressing this pedal reduces the loudness and brightness of the  
sound  
Sostenuto Pedal  
similar to Sustain Pedal, except that notes which are held when  
the sostenuto pedal is pressed are sustained while any new notes  
played after the pedal has been pressed are not sustained  
Stretch Tuning  
Sustain Pedal  
Transpose  
a common acoustic piano tuning method where low strings are  
tuned increasingly flat and high strings are tuned increasingly  
sharp  
pressing this pedal causes played notes to continue sounding  
after the key is released. They will fade or "decay" in a manner  
consistent with the selected instrument  
changes the key of the DG8 ± 1 octave in half-step increments  
DG8 REFERENCE MANUAL  
61  
 
Appendix A: Glossary  
MIDI TERMS  
All Notes Off  
Channel  
a command that is transmitted to all devices in a MIDI system  
that prevents notes from becoming stuck on  
one of sixteen separate “paths” that Voice and Mode data can  
travel on  
Channel Messages data that communicates Voice and Mode messages on a specific,  
user-selected Channel  
Controllers  
MIDI  
commands that are used for musical expression (volume,  
sustain, vibrato, etc.) or remote control of other devices in the  
MIDI system (reverb depth, bank select, etc.)  
“Musical Instrument Digital Interface”; refers to the system of  
connecting microprocessor-controlled instruments and devices  
for sharing information  
MIDI IN  
the port on a device that receives MIDI data  
MIDI OUT  
the port on a device that transmits the MIDI data generated by  
the device  
MIDI THRU  
Mode  
the port on a device that passes received MIDI data to the next  
device in the chain  
a particular state that an instrument or device is currently in;  
in MIDI, “mode” refers to the unit’s receive state that determines  
1. how MIDI messages are received, and 2. how voices will be  
assigned to handle MIDI notes  
Program Change  
a command that instructs the receiving instrument to recall a  
specific sound program from memory  
62  
DG8 REFERENCE MANUAL  
 
Appendix B: Troubleshooting  
TROUBLESHOOTING  
If you experience problems while operating your DG8, please use the following table  
to check for possible causes and solutions before contacting Alesis customer service  
for assistance. Some of them may seem rather obvious, but you’d be amazed at how  
easy it can be to overlook the basics.  
Please note that many problems can be solved simply by re-initializing the DG8 – see  
page 52.  
SYMPTOM  
CAUSE  
No power.  
SOLUTION  
The display does not light  
up when the ON/OFF switch  
is turned on.  
Check that the power cable  
is plugged in properly.  
No sound.  
Volume is turned down  
Raise the VOLUME slider or  
or the volume pedal is at volume pedal if one is  
minimum.  
being used.  
Speakers are turned off.  
Turn speakers on using the  
switch on the back panel.  
MIDI Volume on master Check MIDI Volume level  
controller is set to 0.  
on master MIDI device.  
Local Control is set to  
off.  
Turn Local Control on  
– see page 47.  
Layer sound cannot be  
heard.  
Layer LEVEL slider is  
Raise the LAYER slider.  
Raise the SPLIT slider.  
down.  
Split sound cannot be  
heard.  
Split LEVEL slider is  
down.  
Notes are stuck on.  
MIDI sequencer or  
controller sent an  
incomplete MIDI  
message.  
Step on the sustain pedal  
and release.  
Or select the Basic MIDI  
Channel page and set MIDI  
to off – see page 46.  
I can hear Reverb and/or  
Chorus, but their sliders  
are down.  
MIDI sequencer or  
Move the REVERB or  
controller sent a message CHORUS slider a little to re-  
activate it, then set the  
amount as desired.  
to increase these levels.  
Non-layered piano  
Select the Stretch Tuning  
page and turn it off  
– see page 44.  
Stretch Tuning is on.  
programs are out of tune  
with external MIDI devices  
or other instruments.  
DG8 REFERENCE MANUAL  
 
63  
Appendix B: Troubleshooting  
SYMPTOM  
CAUSE  
SOLUTION  
All programs are out of  
tune with external MIDI  
devices or other  
Master Tune has been  
changed.  
Adjust Master Tune  
– see page 44.  
instruments.  
DG8 is not playing at  
concert pitch.  
Keyboard has been  
transposed.  
Press the TRANSPOSE  
button, then play Middle C  
to set transpose to +00  
– see page 44.  
DG8 sounds chorused or  
tinny even when chorus  
fader is down.  
MIDI Echo turned on in  
a MIDI sequencer, or  
DG8’s Local Control is  
still on while using a  
MIDI sequencer.  
Turn Local Control off in  
the DG8 (see page 47) or  
turn MIDI Echo off in the  
sequencer or computer.  
The AUX pedal is not  
controlling the volume.  
AUX pedal has been set  
to control modulation.  
Set AUX pedal to Volume  
– see page 47.  
The AUX pedal is not  
AUX pedal has been set  
to control volume.  
Set AUX pedal to  
Modulation– see page 47.  
controlling modulation or  
the rotary speaker effect on  
Electric Organ programs.  
The sustain pedal is  
controlling the volume or  
brightness.  
Sustain pedal is plugged Plug the sustain pedal into  
into the SOFT pedal jack.  
the SUSTAIN/SOST jack.  
Soft pedal causes notes to  
sustain.  
Soft pedal is plugged  
into the SUSTAIN/SOST  
jack.  
Plug the soft pedal into the  
SOFT jack.  
64  
DG8 REFERENCE MANUAL  
 
Appendix B: Troubleshooting  
CLEANING AND MAINTENANCE  
While your DG8 should not need much attention, here are some tips for preventive  
maintenance:  
Disconnect the AC power Adapter, then use a damp cloth to clean the DG8’s  
metal and plastic surfaces. For heavy dirt, use a non-abrasive household  
cleaner such as Formula 409® or Fantastik®. DO NOT SPRAY THE  
CLEANER DIRECTLY ONTO THE FRONT OR BACK OF THE UNIT AS IT  
MAY CONTAMINATE THE INTERNAL CARD SLOT CONTACTS, THE  
DISPLAY OR THE FRONT PANEL BUTTONS! Spray onto a cloth, then use  
the cloth to clean the unit.  
Periodically check the power adapter for signs of fraying or damage.  
Unplug the DG8’s AC power adapter when not in use for extended periods  
of time.  
Place a dust cover over the unit when it is not in use.  
Vacuum around the RAM card slot to keep dust from falling into it. DO NOT  
SPRAY ANY KIND OF CLEANER OR LUBRICANT into the card slot.  
The one place where contact cleaner may be useful is on the three 1/4” back  
panel jacks and cables. Periodically disconnect the DG8 from AC power and  
all cables, and clean the 1/4” cable ends with rubbing alcohol or electronic  
contact cleaner, then work the plug into the jack repeatedly. DO NOT SPRAY  
CONTACT CLEANER DIRECTLY INTO THE JACKS. It’s better to use a  
damp plug to clean the jacks, or use a cotton or foam swab (but be careful not  
to get cotton or foam stuck in the unit). While Alesis does not endorse the use  
of any specific product, certain contact enhancers (such as Cramolin™) may  
be used to keep the connections from corroding in the future.  
DG8 REFERENCE MANUAL  
 
65  
Appendix B: Troubleshooting  
66  
DG8 REFERENCE MANUAL  
 
Appendix C: Specifications  
SPECIFICATIONS  
MIDI IMPLEMENTATION CHART  
Function  
Transmitted  
Recognized  
Remarks  
Basic  
Channel  
Default  
Changed  
1 - 3 1  
1 - 16  
1 - 3 1  
1 - 16  
Any three  
consecutive  
Channels.  
Default  
Messages  
Altered  
Mode 3  
X
* * * * * * * *  
9 - 120  
Mode 3  
X
Mode  
Note  
Number  
0 - 127  
0 - 127  
True Voice  
* * * * * * * *  
Velocity  
Note On  
Note Off  
O
O
O
X 2  
After  
Touch  
Keys  
Ch’s  
X
X
X
X 2  
X
O
Pitch Bender  
0
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Bank Select  
1
From AUX pedal  
7
11  
64  
66  
67  
91  
93  
Control  
Change  
Sustain  
Sostenuto  
Soft Pedal  
Reverb Depth  
Chorus Depth  
Prog  
Change  
0 - 59 3, 4  
* * * * * * * *  
0 - 59 3, 4  
0 - 59  
True #  
System  
Exclusive  
X
X
System  
Common  
Song Position  
Song Select  
Tune Request  
X
X
X
X
X
X
System  
Realtime  
Clock  
Commands  
X
X
X
X
Aux  
Local On/Off  
All Notes Off  
Active Sense  
System Reset  
1
X
X
X
X
X
Messages  
X
X
O
CC #121  
Notes:  
Layer Channel sends/receives Program Change/Bank Select only.  
2
3
4
Some card programs may respond to Channel Aftertouch/Note Off value.  
0 - 27 for internal Split Programs.  
0 - 127 for Card Programs.  
Mode 1: OMNI ON, POLY  
Mode 2: OMNI ON, MONO  
Mode 3: OMNI OFF, POLY  
Mode 4: OMNI OFF, MONO  
O : Yes  
X : No  
DG8 REFERENCE MANUAL  
67  
 
Appendix C: Specifications  
SPECIFICATIONS  
Sound Generation Method:  
16 Bit Linear 48kHz Sample ROM with sweepable lowpass filter per voice  
Polyphonic Voices:  
64  
Keyboard Section:  
88 weighted keys, velocity sensitive  
Sound ROM:  
24 MB, expandable to 32 MB via PCMCIA Expansion Card Slot  
Program Memory:  
88 internal preset Programs  
Effects:  
TM  
QS Parallel Matrix Effects (4 independent stereo multieffect processing busses)  
Expansion Slot:  
PCMCIA card slot, will play QCards and cards created with Alesis  
SoundBridge™ software  
Pedal Jacks:  
sustain, sostenuto/soft pedal and AUX (modulation or volume)  
MIDI Jacks:  
In, Out, Thru  
Audio Outputs:  
Stereo (L/R) outputs on 1/4” jacks, 2 headphone outputs on 1/4” TRS jacks  
Audio Inputs:  
Stereo (L/R) inputs on 1/4” jacks  
Dimensions (WxHxD):  
54” x 5.25” x 18.5”  
(1370mm x 133mm x 471mm)  
Weight:  
80 lbs. (36.3kg)  
68  
DG8 REFERENCE MANUAL  
 
Appendix D: Warranty  
WARRANTY  
This product is warranted by Alesis to the original purchaser against defects in  
material and workmanship for a period of 1 year for parts and labor from the date of  
purchase. Complete terms of the Limited Warranty are stated on the Warranty Card  
packed with the product. Please retain a copy of your dated sales receipt for proof of  
warranty status should repairs be necessary.  
REFER ALL SERVICING TO ALESIS  
We believe that the DG8 should provide years of trouble-free use. However, should  
problems occur, DO NOT attempt to service the unit yourself. Service on this product  
should be performed only by qualified technicians. THERE ARE NO USER-  
SERVICEABLE PARTS INSIDE.  
OBTAINING REPAIR SERVICE  
Before contacting Alesis, check over all your connections, and make sure you’ve read  
the manual. Your Alesis dealer may be able to offer further assistance.  
Customers in the USA:  
If the problem persists, copy down the serial number of your DG8 and call Alesis  
USA at 1-800-5-ALESIS and request the Technical Support Department. Talk the  
problem over with one of our technicians; if necessary, you will be given a return  
authorization (RA) number and instructions on how to return the unit to Alesis or  
the nearest authorized service center. All units must be shipped prepaid and COD  
shipments will not be accepted.  
You must indicate the RA number on the shipping label or the shipment will not be  
accepted. If you do not have the original packing, ship the DG8 in a sturdy carton  
with shock-absorbing materials such as foam or “bubble-pack” surrounding the unit.  
Shipping damage caused by inadequate packing is not covered by the Alesis  
warranty. Ship the unit with insurance via a carrier that provides a tracking system.  
Tape a note to the top of the unit describing the problem, include your name and a  
phone number where Alesis can contact you if necessary, as well as instructions on  
where you want the product returned. Alesis will pay for standard one-way shipping  
back to you on any repair covered under the terms of this warranty.  
Field repairs are not authorized during the warranty period, and repair attempts by  
unqualified personnel may invalidate the warranty.  
Customers outside the USA:  
Contact your local Alesis dealer for warranty assistance. Do not return products to  
the factory unless you have been given specific instructions to do so. Your warranty  
is valid only in the country of purchase.  
Internet Addresses:  
Important information and advice is available on our web site:  
E-mail may be addressed to: [email protected]  
DG8 REFERENCE MANUAL  
 
69  
Appendix D: Warranty  
70  
DG8 REFERENCE MANUAL  
 
Index  
INDEX  
FCC information...............................................12  
A
G
AC power .......................................................... 19  
Alesis contact information ............................... 4  
arrow buttons ................................................... 27  
tutorial ..................................................... 33–34  
audio outputs.................................................... 51  
AutoDemos....................................................... 23  
graphic equalizer........................................29, 45  
I
initializing..........................................................52  
K
Keyboard Banks, defined..........................23, 31  
Keyboard Scaling function .............................47  
B
Bass Banks, defined................................... 23, 32  
L
C
LAYER LEVEL slider.......................................27  
LAYER/OFF button................ 25, 37, 39, 40, 41  
Layers  
Card Bank, defined.................................... 24, 32  
Card sounds  
as Primary Programs................................... 40  
in a Layer  
as both Primary and Layer .................... 41  
as the Layer sound .................................. 40  
as the Primary Program ......................... 41  
in a Split  
defined .............................................. 25, 36, 61  
tutorial......................................................36–37  
M
Master Tune............................See TUNE button  
MIDI  
as both Primary and Split sound .......... 41  
as the Primary Program ......................... 41  
as the Split sound..................................... 41  
in a Split-with-Layer ................................... 42  
using the Alesis QCard............................... 40  
CE Declaration of Conformity....................... 13  
Chorus.................................................. See effects  
Cleaning and maintenance............................. 65  
connections........................................................ 19  
DG8 as MIDI master.................................... 20  
DG8 as MIDI slave....................................... 21  
DG8 with MIDI patchbay........................... 22  
pedals............................................................. 49  
Continuous Controllers .................................. 55  
cursor............................................................ 27, 33  
Channel function..........................................29  
Channel Mode Messages............................57  
Channel Voice Messages.............................54  
DG8 functions  
Bass Sustain...............................................47  
Channel messages  
Basic Channel .................................29, 46  
Program Change commands .............59  
Local Control.............................................47  
Sustain Catching.......................................47  
list of controller numbers............................56  
MIDI defined...........................................53, 62  
MIDI Implementation chart  
defined ...........................................................53  
DG8 MIDI chart............................................67  
D
P
DG8 setup  
pedals  
AC power...................................................... 19  
basics.............................................................. 17  
music stand................................................... 18  
setting up in the home................................ 19  
sustain pedal................................................. 19  
unpacking...................................................... 17  
using in a music system.............................. 20  
using with other equipment ...................... 17  
DG8 sound chart.............................................. 43  
display................................................................ 33  
AUX Pedal assignment ...............................47  
connections....................................................49  
rocker pedals.................................................50  
sostenuto pedal.............................................49  
sustain pedal .................................................48  
tutorial............................................................48  
volume and modulation pedals ................50  
PLAY button......................................................27  
power-up reset function..................................52  
Primary Programs, defined............... 25, 32, 35  
E
R
effects.................................................................. 45  
Reverb...................................................See effects  
F
factory defaults................................................. 52  
DG8 REFERENCE MANUAL  
71  
 
Index  
S
Split-with-Layer  
defined ...........................................................26  
tutorial............................................................39  
sustain pedal .....................................................19  
Sustain Pedal Catching....................................48  
Safety Instructions  
English ............................................................. 7  
French .............................................................. 9  
German.......................................................... 11  
selecting sounds............................................... 35  
SET SPLIT button....................................... 26, 39  
Single mode, defined................................. 25, 35  
Sound Slection buttons ................................... 33  
specifications..................................................... 68  
SPLIT LEVEL slider......................................... 27  
SPLIT/OFF button.........................26, 39, 40, 41  
Splits  
T
TRANSPOSE button ..................................28, 44  
Troubleshooting................................................63  
TUNE button........................................ 23, 28, 44  
U
unpacking ..........................................................17  
V
defined..................................................... 26, 36  
tutorial ..................................................... 36–39  
VOLUME LEVEL slider..................................27  
W
Warranty information .....................................69  
72  
DG8 REFERENCE MANUAL  
 

Accton Technology Switch 12i User Manual
Acesonic Karaoke Machine KOD 800 User Manual
ADC Network Hardware ISDN NT11010 User Manual
Aiwa CD Player NSX MT241 User Manual
Alpine Car Stereo System MRP M2000 User Manual
Amana Refrigerator ABB2221FEB1 User Manual
Atmel Computer Accessories AT91EB42 User Manual
Audiovox Automobile Alarm PRO9801 User Manual
Aviom Musical Instrument A 16CS User Manual
Beko Clothes Dryer DRVT 61 W User Manual